View CS49400_40297.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CS49400 Family DSP Multi-Standard Audio Decoder
Features
CS49300 Legacy Audio Decoder Support Dolby Digital EXTM, Dolby Pro Logic IITM DTS-ES 96/24TM, DTS 96/24TM, DTS-ES Discrete 6.1TM, DTS-ES Matrix 6.1TM, DTS Digital SurroundTM and DTS Virtual 5.1TM MPEG-2: AAC Multichannel 5.1 MPEG Multichannel and Musicam MPEG-1/2, Layer III (MP3) DTS Neo:6TM, LOGIC7(R), SRS Circle Surround IITM Cirrus Extra SurroundTM, Cirrus Original Surround 6.1 (C.O.S. 6.1)TM THX Surround EXTM, THX Ultra2 CinemaTM 12-Channel Serial Audio Inputs Integrated 8K Byte Input Buffer Powerful 32-bit Audio DSP Customer Software Security Keys Large On-chip X,Y, and Program RAM Supports SDRAM, SRAM, FLASH memories 16-channel PCM output Dual S/PDIF Transmitters SPI Serial, and Motorola(R) and Intel(R) Parallel Host Control Interfaces GPIO support for all common sub-circuits
Description
The CS49400 Audio Decoder DSP is targeted as a marketspecific consumer entertainment processor for AV Receivers and DVD Audio/Video Players. The device is constructed using an enhanced version of the CS49300 Family DSP audio decoder followed by a 32-bit programmable post-processor DSP, which gives the designer the ability to add product differentiation through the Cirrus FrameworkTM programming structure and Framework module library. Dolby Digital Pro Logic II, DTS Digital Surround, MPEG Multichannel, and Cirrus Original Surround 6.1 PCM Effects Processor (capable of generating such DSP audio modes as: Hall, Theater, Church) are included in the cost of the CS49400 Family DSP. Additional algorithms available through the Crystal WareTM Software Licensing Program, give the designer the ability to further deliver end-product differentiation. The CS49400 contains sufficient on-chip SRAM to support decoding all major audio decoding algorithms available today including: AAC Multichannel, DTS 96/24, DTS-ES 96/24. The CS49400 also supports a glueless SDRAM/SRAM for increased all-channel delays. The SRAM interface also supports connection to an external byte-wide EPROM for code storage or Flash memory thus allowing products to be fieldupgradable as new audio algorithms are developed. This chip, teamed with Crystal WareTM certified decoder library, Cirrus digital interface products and mixed signal data converters, enables the conception and design of next generation digital entertainment products.
Ordering Information: See page 98
SAI 0 SAI 1 SAI 2 SAI 3
Serial Audio Interface
External Memory Interface
Internal Bus
Compressed Digital Interface Digital Audio Input
DSP C
Shared Memory
Frame Shifter Multi-Standard Audio Decoder Programmable 32-Bit DSP
Digital Audio Output
DAO 0 DAO 1
DSP AB
PLL Clock Manager
Input Buffer RAM
Parallel or Serial Host Interface
DSP RAM
DSP ROM
GPIO and I/O Controller Parallel or Serial Host Interface
Preliminary Product Information
This document contains information for a new product. Cirrus Logic reserves the right to modify this product without notice.
P.O. Box 17847, Austin, Texas 78760 (512) 445 7222 FAX: (512) 445 7581 http://www.cirrus.com
Copyright Cirrus Logic, Inc. 2002 (All Rights Reserved)
JUL `02 DS536PP2 1
(c)
TABLE OF CONTENTS
1.0 CHARACTERISTICS AND SPECIFICATIONS ...................................................................... 8 1.1 Absolute Maximum Ratings ............................................................................................... 8 1.2 Recommended Operating Conditions ................................................................................ 8 1.3 Digital D.C. Characteristics for VDD Level I/O ................................................................... 8 1.4 Digital D.C. Characteristics for VDDSD Level I/O .............................................................. 9 1.5 Power Supply Characteristics ............................................................................................ 9 1.6 Switching Characteristics-- RESET .................................................................................. 9 1.7 Switching Characteristics -- CLKIN ................................................................................. 10 1.8 Switching Characteristics -- Intel(R) Host Slave Mode (DSPAB) ...................................... 11 1.9 Switching Characteristics -- Intel(R) Host Slave Mode (DSPC) ........................................ 13 1.10 Switching Characteristics -- Motorola(R) Host Slave Mode (DSPAB) ............................ 15 1.11 Switching Characteristics -- Motorola(R) Host Slave Mode (DSPC) .............................. 17 1.12 Switching Characteristics -- SPI Control Port Slave Mode (DSPAB) ............................ 19 1.13 Switching Characteristics -- SPI Control Port Slave Mode (DSPC) .............................. 21 1.14 Switching Characteristics -- Digital Audio Input (DSPAB) ............................................ 23 1.15 Switching Characteristics -- Serial Audio Input (DSPC) ............................................... 24 1.16 Switching Characteristics -- CMPDAT, CMPCLK (DSPAB) ......................................... 25 1.17 Switching Characteristics -- Parallel Data Input (DSPAB) ............................................ 26 1.18 Switching Characteristics -- Digital Audio Output ......................................................... 27 1.19 Switching Characteristics -- SRAM/FLASH Interface ................................................... 29 1.20 Switching Characteristics -- SDRAM Interface ............................................................. 31 2. OVERVIEW ............................................................................................................................. 35
Contacting Cirrus Logic Support
For a complete listing of Direct Sales, Distributor, and Sales Representative contacts, visit the Cirrus Logic web site at: http://www.cirrus.com/corporate/contacts/sales.cfm
Dolby Digital, Dolby Digital EX, AC-3, Dolby Pro Logic, Dolby Pro Logic II, Dolby Digital EX Pro Logic II, Dolby Surround, Dolby Surround Pro Logic II, Surround EX, Virtual Dolby Digital and the "AAC" logo are trademarks and the "Dolby" and the double-"D" symbol are registered trademarks of Dolby Laboratories Licensing Corporation. DTS, DTS Digital Surround, DTS-ES Extended Surround, DTS 96/24, DTS-ES 96/24, DTS Neo:6, and DTS Virtual 5.1 are trademarks and the "DTS", "DTS Digital Surround", "DTS-ES", "DTS 96/24", "DTS-ES 96/24", "DTS Neo:6", "DTS Virtual 5.1" logos are registered trademarks of the Digital Theater Systems Corporation. The "MPEG Logo" is a registered trademark of Philips Electronics N.V. THX Ultra2 Cinema, Timbre-Matching, Re-EQ, Adapative Decorrelation and THX are trademarks or registered trademarks of Lucasfilm, Ltd. Surround EX is a jointly developed technology of THX and Dolby Labs, Inc. AAC (Advanced Audio Coding) is an "MPEG-2-standard-based" digital audio compression algorithm (offering up 5.1 discrete decoded channels for this implementation) collaboratively developed by AT&T, the Fraunhofer Institute, Dolby Laboratories, and the Sony Corporation. In regards to the MP3 capable functionality of the CS494XX Family DSP (via downloading of mp3_ab_494xxx_vv.uld application code) the following statements are applicable: "Supply of this product conveys a license for personal, private and non-commercial use. MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and THOMSON Multimedia." VMAx is a registered trademark of Harman International. The LOGIC7 logo and LOGIC7 are registered trademarks of Lexicon. SRS CircleSurround, SRS Circle Suround II, SRS TruSurround, and SRS TruSurround XT are trademarks of SRS Labs, Inc. The HDCD logo, HDCD, High Definition Compatible Digital and Pacific Microsonics are either registered trademarks or trademarks of Pacific Microsonics, Inc. in the United States and/or other countries. HDCD technology provided under license from Pacific Microsonics, Inc. This product's software is covered by one or more of the following in the United States: 5,479,168; 5,638,074; 5,640,161; 5,872,531; 5,808,574; 5,838,274; 5,854,600; 5,864,311; and in Australia: 669114; with other patents pending. Intel is a registered trademark of Intel Corporation. Motorola is a registered trademark of Motorola, Inc. I2C is a registered trademark of Philips Semiconductor. Purchase of I2C Components of Cirrus Logic, Inc., or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use those components in a standard I2C system. "Crystal Ware", "Cirrus Framework", "Cirrus Extra Surround", "Cirrus Triple Crossover Bass Management", "Cirrus Quadruple Crossover Bass Management" and "Cirrus Original Surround 6.1" are trademarks and "Cirrus Logic" is a registered trademarks of Cirrus Logic, Inc. All other names are trademarks, registered trademarks, or service marks of their respective companies. Preliminary product information describes products which are in production, but for which full characterization data is not yet available. Advance product information describes products which are in development and subject to development changes. Cirrus Logic, Inc. has made best efforts to ensure that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). No responsibility is assumed by Cirrus Logic, Inc. for the use of this information, nor for infringements of patents or other rights of third parties. This document is the property of Cirrus Logic, Inc. and implies no license under patents, copyrights, trademarks, or trade secrets. No part of this publication may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photographic, or otherwise) without the prior written consent of Cirrus Logic, Inc. Items from any Cirrus Logic website or disk may be printed for use by the user. However, no part of the printout or electronic files may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photographic, or otherwise) without the prior written consent of Cirrus Logic, Inc.Furthermore, no part of this publication may be used as a basis for manufacture or sale of any items without the prior written consent of Cirrus Logic, Inc. The names of products of Cirrus Logic, Inc. or other vendors and suppliers appearing in this document may be trademarks or service marks of their respective owners which may be registered in some jurisdictions. A list of Cirrus Logic, Inc. trademarks and service marks can be found at http://www.cirrus.com.
2
2.1 DSPAB ............................................................................................................................ 36 2.2 DSPC ............................................................................................................................... 36 3. TYPICAL CONNECTION DIAGRAMS ................................................................................... 37 3.1 Multiplexed Pins .............................................................................................................. 37 3.2 Termination Requirements .............................................................................................. 37 3.3 Phase Locked Loop Filter ................................................................................................ 37 4. POWER .............................................................................................................................. 38 4.1 Decoupling ....................................................................................................................... 38 4.2 Analog Power Conditioning ............................................................................................. 38 4.3 Ground ............................................................................................................................. 38 4.4 Pads ................................................................................................................................ 38 5. CLOCKING ............................................................................................................................. 42 6. CONTROL .............................................................................................................................. 42 6.1 Serial Communication ..................................................................................................... 42 6.1.1 SPI Communication for DSPAB .......................................................................... 42 6.1.2 SPI Communication for DSPC ............................................................................ 46 6.1.3 FINTREQ Behavior: A Special Case .................................................................. 49 6.2 Parallel Host Communication for DSPAB ........................................................................ 51 6.2.5 Intel Parallel Host Communication Mode for DSPAB ......................................... 51 6.2.6 Motorola Parallel Communication Mode for DSPAB ........................................... 54 6.2.7 Procedures for Parallel Host Mode Communication for DSPAB ......................... 56 6.3 Parallel Host Communication for DSPC .......................................................................... 58 6.3.5 Intel Parallel Host Communication Mode for DSPC ............................................ 60 6.3.6 Motorola Parallel Host Communication Mode for DSPC .................................... 64 6.3.7 Procedures for Parallel Host Mode Communication for DSPC ........................... 68 7. EXTERNAL MEMORY ............................................................................................................ 70 7.1 Configuring SRAM Timing Parameters ........................................................................... 71 8. BOOT PROCEDURE .............................................................................................................. 72 8.1 Host Controlled Master Boot ........................................................................................... 72 8.2 Host Boot Via DSPC ........................................................................................................ 75 9. SOFT RESETTING THE CS49400 ......................................................................................... 77 9.1 Host Controlled Master Soft Reset .................................................................................. 77 10. HARDWARE CONFIGURATION ......................................................................................... 79 11. DIGITAL INPUT AND OUTPUT DATA FORMATS .............................................................. 79 11.1 Digital Audio Formats .................................................................................................... 79 11.1.1 I2S ..................................................................................................................... 79 11.1.2 Left Justified ...................................................................................................... 79 11.2 Digital Audio Input Port .................................................................................................. 79 11.3 Compressed Data Input Port ......................................................................................... 80 11.4 Input Data Hardware Configuration for CDI and DAI on DSPAB ................................. 80 11.4.1 Input Configuration Considerations ................................................................ 81 11.5 Serial Audio Input .......................................................................................................... 82 11.6 Digital Audio Output Port ............................................................................................... 82 11.6.1 S/PDIF Outputs ................................................................................................. 83 11.7 Output Data Hardware Configuration ............................................................................ 84 11.8 Creating Hardware Configuration Messages ................................................................. 85 12.0 PIN DESCRIPTION ............................................................................................................. 87 12.1 144-Pin LQFP Package Pin Layout ............................................................................... 87 12.2 100-Pin LQFP Package Pin Layout ............................................................................... 88 12.3 Pin Definitions ................................................................................................................ 89 13. ORDERING INFORMATION ................................................................................................ 99 14. PACKAGE DIMENSIONS .................................................................................................. 100 14.1 144-Pin LQFP Package ............................................................................................... 100
3
LIST OF FIGURES
Figure 1. RESET Timing ..................................................................................................................... 9 Figure 2. CLKIN with CLKSEL = VSS = PLL Enable ........................................................................ 10 Figure 3. Intel(R) Parallel Host Mode Slave Read Cycle for DSPAB .................................................. 12 Figure 4. Intel(R) Parallel Host Mode Slave Write Cycle for DSPAB ................................................... 12 Figure 5. Intel(R) Parallel Host Slave Mode Read Cycle for DSPC ..................................................... 14 Figure 6. Intel(R) Parallel Host Slave Mode Write Cycle for DSPC ..................................................... 14 Figure 7. Motorola(R) Parallel Host Slave Mode Read Cycle for DSPAB ........................................... 16 Figure 8. Motorola(R) Parallel Host Slave Mode Write Cycle for DSPAB ........................................... 16 Figure 9. Motorola(R) Parallel Host Slave Mode Read Cycle for DSPC ............................................. 18 Figure 10. Motorola(R) Parallel Host Slave Mode Write Cycle for DSPC ............................................ 18 Figure 11. SPI Control Port Slave Mode Timing (DSPAB) ............................................................... 20 Figure 12. SPI Control Port Slave Mode Timing (DSPC) ................................................................. 22 Figure 13. Digital Audio Input Data, Slave Clock Timing .................................................................. 23 Figure 14. Serial Audio Input Data, Slave Clock Timing ................................................................... 24 Figure 15. Serial Compressed Data Timing ...................................................................................... 25 Figure 16. Parallel Data Timing ........................................................................................................ 26 Figure 17. Digital Audio Output Data, Input and Output Clock Timing ............................................. 28 Figure 18. Digital Audio Output Data, Input and Output Clock Timing ............................................. 28 Figure 19. SRAM/Flash Controller Timing Diagram - Write Cycle .................................................... 29 Figure 20. SRAM/Flash Controller Timing Diagram - Read Cycle .................................................... 29 Figure 21. SRAM/Flash Controller Timing Diagram - Single Byte Write Cycle ................................. 30 Figure 22. SRAM/Flash Controller Timing Diagram - Single Byte Read Cycle ................................ 30 Figure 23. SDRAM Controller Timing Diagram - Load Mode Register Cycle ................................... 31 Figure 24. SDRAM Controller Timing Diagram - Burst Write Cycle .................................................. 32 Figure 25. SDRAM Controller Timing Diagram - Burst Read Cycle ................................................. 33 Figure 26. SDRAM Controller Timing Diagram - Auto Refresh Cycle .............................................. 34 Figure 27. SPI Control with External Memory - 144 Pin Package .................................................... 39 Figure 28. Intel(R) Parallel Control Mode - 144 Pin Package .............................................................. 40 Figure 29. Motorola(R) Parallel Control Mode - 144 Pin Package ....................................................... 41 Figure 30. SPI Write Flow Diagram for DSPAB ................................................................................ 43 Figure 31. SPI Timing for DSPAB ..................................................................................................... 44 Figure 32. SPI Read Flow Diagram for DSPAB ................................................................................ 45 Figure 33. SPI Write Flow Diagram for DSPC .................................................................................. 46 Figure 34. SPI Timing for DSPC ....................................................................................................... 47 Figure 35. SPI Read Flow Diagram for DSPC .................................................................................. 48 Figure 36. Intel Mode, One-Byte Write Flow Diagram for DSPAB .................................................... 53 Figure 37. Intel Mode, One-Byte Read Flow Diagram for DSPAB ................................................... 54 Figure 38. Motorola Mode, One-Byte Write Flow Diagram for DSPAB ............................................ 55 Figure 39. Motorola Mode, One-Byte Read Flow Diagram for DSPAB ............................................ 55 Figure 40. Typical Parallel Host Mode Control Write Sequence Flow Diagram for DSPAB ............. 56 Figure 41. Typical Parallel Host Mode Control Read Sequence Flow Diagram for DSPAB ............. 57
4
Figure 42. Intel Mode, One-Byte Write Flow Diagram for DSPC .......................................................60 Figure 44. Intel Mode, One-Byte Read Flow Diagram for DSPC ......................................................61 Figure 43. Intel Mode, 32-bit (4-byte) Write Flow Diagram for DSPC .............................................................................................................................62 Figure 45. Intel Mode, 32-Bit (4-Byte) Read Flow Diagram for DSPC .............................................................................................................................63 Figure 46. Motorola Mode, One-Byte Write Flow Diagram for DSPC .............................................................................................................................64 Figure 47. Motorola Mode, 32-bit (4-byte) Write Flow Diagram for DSPC ........................................65 Figure 48. Motorola Mode, One-Byte Read Flow Diagram for DSPC .............................................................................................................................66 Figure 49. Motorola Mode, 32-Bit (4-Byte) Read Flow Diagram for DSPC .......................................67 Figure 50. Typical Parallel Host Mode Control Write Sequence Flow Diagram for DSPC ................68 Figure 51. Typical Parallel Host Mode Control Read Sequence Flow Diagram for DSPC ................69 Figure 52. Host Controlled Master Boot (Downloading both a DSPAB Application Code and a DSPC Application Code) ..............................73 Figure 53. Host Boot Via DSPC .......................................................................................................76 Figure 54. Host Controlled Master Softreset .....................................................................................78 Figure 55. I2S Format ........................................................................................................................80 Figure 56. Left Justified Format (Rising Edge Valid SCLK) ...............................................................80 Figure 57. Pin Layout (144-Pin LQFP Package) ...............................................................................87 Figure 58. Pin Layout (100-Pin LQFP Package) ...............................................................................88 Figure 59. 144-Pin LQFP Package Drawing ...................................................................................100
5
LIST OF TABLES
Table 1. PLL Filter Component Values ...............................................................................................37 Table 2. Host Modes for DSPAB ........................................................................................................42 Table 3. Host Modes for DSPC ..........................................................................................................42 Table 4. SPI Communication Signals for DSPAB ...............................................................................43 Table 5. SPI Communication Signals for DSPC .................................................................................46 Table 6. Intel Mode Communication Signals for DSPAB ....................................................................51 Table 6. Parallel Input/Output Registers for DSPAB ..........................................................................52 Table 7. Motorola Mode Communication Signals for DSPAB.............................................................54 Table 8. Parallel Input/Output Registers for DSPC.............................................................................59 Table 9. Intel Mode Communication Signals for DSPC ......................................................................60 Table 10. Motorola Mode Communication Signals for DSPC .............................................................64 Table 11. SRAM Interface Pins ..........................................................................................................70 Table 12. SDRAM Interface Pins ........................................................................................................70 Table 13. SRAM Controller Timing .....................................................................................................71 Table 14. SDRAM Config Register .....................................................................................................71 Table 15. Application Messages from DSPAB ...................................................................................72 Table 16. Boot Write Messages for DSPC .........................................................................................72 Table 17. Boot Read Messages from DSPC ......................................................................................72 Table 18. Digital Audio Input Port .......................................................................................................80 Table 19. Compressed Data Input Port ..............................................................................................80 Table 20. Input Data Type Configuration (Input Parameter A).............................................................................................................81 Table 21. Input Data Format Configuration (Input Parameter B).............................................................................................................81 Table 22. Input SCLK Polarity Configuration (Input Parameter C) ............................................................................................................81 Table 23. Serial Audio Input Port ........................................................................................................82 Table 24. SAI Data Type Configuration (Input Parameter D) ............................................................................................................82 Table 25. Digital Audio Output Port ....................................................................................................82 Table 26. MCLK/SCLK Master Mode Ratios ......................................................................................83 Table 27. Output Clock Configuration (Parameter A)......................................................................................................................84 Table 28. Output Data Configuration Parameter B)...........................................................................84 Table 29. Output SCLK/LRCLK Configuration (Parameter C) .....................................................................................................................84 Table 30. Output SCLK Polarity Configuration (Parameter D) .....................................................................................................................85 Table 31. Example Values to be Sent to DSPAB After Download or Soft Reset................................86 Table 32. Example Values to be Sent to DSPC After Download or Soft Reset ..................................86
6
1.0 CHARACTERISTICS AND SPECIFICATIONS
Note: All data sheet minimum and maximum timing parameters are guaranteed over the rated voltage and temperature. Actual production testing is performed at TA = 25 C with an appropriate guardband to guarantee minimum and maximum timing specifications over rated voltage and temperature.
1.1 Absolute Maximum Ratings
(VSS, VSSSD, PLLVSS = 0 V; all voltages with respect to 0 V) Parameter DC power supplies: Core supply PLL supply Memory supply ||PLLVDD| - |VDD|| Symbol VDD PLLVSS VDDSD Iin Vind Vinsd Tstg Min -0.3 -0.3 -0.3 -65 Max 2.7 2.7 3.6 0.3 10 3.6 3.6 150 Unit V V V V mA V V C
Input current, any pin except supplies Digital input voltage on I/O pins powered from VDD Digital input voltage on I/O pins powered from VDDSD Storage temperature
Caution: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes.
1.2 Recommended Operating Conditions
(VSS, VSSSD, PLLVSS = 0 V; all voltages with respect to 0 V) Parameter DC power supplies: Core supply PLL supply Memory supply ||PLLVDD| - |VDD|| Symbol VDD PLLVSS VDDSD TA Min 2.37 2.37 3.15 0 Typ 2.5 2.5 3.3 Max 2.63 2.63 3.45 0.3 70 Unit V V V V C
Ambient operating temperature
1.3 Digital D.C. Characteristics for VDD Level I/O
(TA = 25 C;VDD = 2.5 V; measurements performed under static conditions.) Parameter High-level input voltage Low-level input voltage High-level output voltage at IO = -2.0 mA Low-level output voltage at IO = 2.0 mA Input leakage current (all pins without internal pullup resistors except CLKIN) Input leakage current (pins with internal pull-up resistors, CLKIN) Symbol VIH VIL VOH VOL Iin Min 2.0 VDD x 0.9 Typ Max 0.8 VDD x 0.1 10 50 Unit V V V V A A
7
1.4 Digital D.C. Characteristics for VDDSD Level I/O
(TA = 25 C;VDDSD = 3.3 V; measurements performed under static conditions.) Parameter High-level input voltage Low-level input voltage High-level output voltage at IO = -2.0 mA Low-level output voltage at IO = 2.0 mA Input leakage current (except all pins with internal pullup) Input leakage current (all pins with internal pull-up) Symbol VIH VIL VOH VOL Iin 0.9xVDDSD 0.1xVDDSD 10 50 Min 0.65xVDDSD 0.35xVDDSD Typ Max Unit V V V V A A
1.5 Power Supply Characteristics
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V;measurements performed under operating conditions) Parameter Power supply current: Core and I/O operating: VSS PLL operating: PLLVSS Memory operating: VSSSD Symbol Min Typ 400 6 25 Max Unit mA mA mA
1.6 Switching Characteristics-- RESET
(TA = 25 C; VDD, PLLVDD= 2.5 V; VDDSD = 3.3 V; CL = 20 pF) Parameter RESET minimum pulse width low All bidirectional pins high-Z after RESET low Configuration bits setup before RESET high Configuration bits hold after RESET high Symbol Trstl Trst2z Trstsu Trsthld 50 15 Min 10 Max 50 Unit s ns ns ns
RESET FHS0,1,2 UHS0,1,2 All Bidirectional Pins Trst2z Trstl
T rstsu Trsthld
Figure 1. RESET Timing
8
1.7 Switching Characteristics -- CLKIN
(TA = 25 C; VDD, PLLVDD = 2.5; VDDSD = 3.3 V; CL = 20 pF) Parameter CLKIN period for internal DSP clock mode CLKIN high time for internal DSP clock mode CLKIN low time for internal DSP clock mode External Crystal operating frequency Symbol Tclki Tclkih Tclkil Fxtal Min 35 18 18 10 14 Max 100 Unit ns ns ns MHz
CLKIN
Tclkih Tclki
Tclkil
Figure 2. CLKIN with CLKSEL = VSS = PLL Enable
9
1.8 Switching Characteristics -- Intel(R) Host Slave Mode (DSPAB)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Unit
Address setup before FCS and FRD low or FCS and FWR low Address hold time after FCS and FRD low or FCS and FWR high
Read
Tias Tiah
5 5
-
ns ns
Delay between FRD then FCS low or FCS then FRD low Data valid after FCS and FRD low FCS and FRD low for read Data hold time after FCS or FRD high Data high-Z after FCS or FRD high FCS or FRD high to FCS and FRD low for next read (Note 1) FCS or FRD high to FCS and FWR low for next write (Note 1)
Write
Ticdr Tidd Tirpw Tidhr Tidis Tird Tirdtw Ticdw Tidsu Tiwpw Tidhw Tiwtrd Tiwd
0 DCLKP + 10 5 2*DCLKP + 10 2*DCLKP + 10 0 20 DCLKP + 10 5 2*DCLKP + 10 2*DCLKP + 10
21 22 -
ns ns ns ns ns ns ns ns ns ns ns ns ns
(Note 1)
Delay between FWR then FCS low or FCS then FWR low Data setup before FCS or FWR high FCS and FWR low for write Data hold after FCS or FWR high FCS or FWR high to FCS and FRD low for next read (Note 1) FCS or FWR high to FCS and FWR low for next write (Note 1) (Note 1)
Notes: 1. Certain timing parameters are normalized to the DSP clock period, DCLKP. DCLKP = 1/DCLK. The DSP clock can be defined as follows: Internal Clock Mode: DCLK ~ 60MHz before and during boot, i.e. DCLKP ~ 16.6ns DCLK ~ 86 MHz after boot, i.e. DCLKP ~ 11.6ns It should be noted that DCLK for the internal clock mode is application specific. The application code users guide should be checked to confirm DCLK for the particular application.
10
F A1:0 T ia h F DAT A7:0 F CS
Ticdr Tias Tidd
Tidhr Tidis
FWR F RD
Tirpw
Tird
Tirdtw
Figure 3. Intel(R) Parallel Host Mode Slave Read Cycle for DSPAB
F A1:0
T iah F DATA7:0 F CS Ticdw F RD F WR T iw pw Tidsu Tiw d Tiw trd Tias
Tid hw
Figure 4. Intel(R) Parallel Host Mode Slave Write Cycle for DSPAB
11
1.9 Switching Characteristics -- Intel(R) Host Slave Mode (DSPC)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Unit
Address setup before CS and RD low or CS and WR low Address hold time after CS and RD low or CS and WR low
Read
Tias Tiah Ticdr Tidd
DCLKP DCLKP+15 0 2*DCLKP DCLKP+10 2*DCLKP+10 2*DCLKP+10 0 2*DCLKP+10 2*DCLKP DCLKP 2*DCLKP+10 2*DCLKP+10
2*DCLKP+ 25 2*DCLKP+ 10 -
ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Delay between RD then CS low or CS then RD low Data valid after CS and RD low CS and RD low for read Data hold time after CS or RD high Data high-Z after CS or RD high CS or RD high to CS and RD low for next read CS or RD high to CS and WR low for next write
Write
(Note 1)
Tirpw Tidhr Tidis
(Note 1) (Note 1)
Tird Tirdtw Ticdw Tidsu
Delay between WR then CS low or CS then WR low Data setup before CS or WR high CS and WR low for write Data hold after CS or WR high CS or WR high to CS and RD low for next read CS or WR high to CS and WR low for next write (Note 1) (Note 1) (Note 1)
Tiwpw Tidhw Tiwtrd Tiwd
Notes: 1. Certain timing parameters are normalized to the DSP clock, DCLKP, in nanoseconds. DCLKP = 1/DCLK. The DSP clock can be defined as follows: Internal Clock Mode: DCLK ~ 60MHz before and during boot, i.e. DCLKP ~ 16.6ns DCLK ~ 86 MHz after boot, i.e. DCLKP ~ 11.6ns It should be noted that DCLK for the internal clock mode is application specific. The application code users guide should be checked to confirm DCLK for the particular application.
12
A1:0 Tiah DATA7:0 CS Ticdr WR RD Tirpw Tias Tidd Tidhr Tidis Tird Tirdtw
Figure 5. Intel(R) Parallel Host Slave Mode Read Cycle for DSPC
A1:0 Tiah DATA7:0 CS Ticdw RD WR Tiwpw Tidsu Tiwd Tiwtrd Tias Tidhw
Figure 6. Intel(R) Parallel Host Slave Mode Write Cycle for DSPC
13
1.10 Switching Characteristics -- Motorola(R) Host Slave Mode (DSPAB)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Unit
Address setup before FCS and FDS low Address hold time after FCS and FDS low
Read
Tmas Tmah Tmcdr Tmdd (Note 1) Tmrpw Tmdhr Tmdis Tmrd Tmrdtw Tmcdw Tmdsu (Note 1) Tmwpw Tmrwsu Tmrwhld Tmdhw Tmwtrd Tmwd
5 5 0 DCLKP + 10 5 2*DCLKP + 10 2*DCLKP + 10 0 20 DCLKP + 10 5 5 5 2*DCLKP + 10 2*DCLKP + 10
21 22 -
ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Delay between FDS then FCS low or FCS then FDS low Data valid after FCS and FRD low with R/W high) FCS and FDS low for read Data hold time after FCS or FDS high after read Data high-Z after FCS or FDS high after read FCS or FDS high to FCS and FDS low for next read (Note 1) FCS or FDS high to FCS and FDS low for next write(Note 1)
Write
Delay between FDS then FCS low or FCS then FDS low Data setup before FCS or FDS high FCS and FDS low for write R/W setup before FCS AND FDS low R/W hold time after FCS or FDS high Data hold after FCS or FDS high FCS or FDS high to FCS and FDS low with R/W high for next read (Note 1) FCS or FDS high to FCS and FDS low for next write(Note 1)
Notes: 1. Certain timing parameters are normalized to the DSP clock, DCLKP, in nanoseconds. DCLKP = 1/DCLK. The DSP clock can be defined as follows: Internal Clock Mode: DCLK ~ 60MHz before and during boot, i.e. DCLKP ~ 16.6ns DCLK ~ 86 MHz after boot, i.e. DCLKP ~ 11.6ns It should be noted that DCLK for the internal clock mode is application specific. The application code users guide should be checked to confirm DCLK for the particular application.
14
F A1:0 Tmah F DATA7:0 FCS FR/W F DS
Tmas Tmdd Tmrwsu Tmcdr Tmrpw Tmrd Tmdis Tmrdtw Tmrwhld Tmdhr
Figure 7. Motorola(R) Parallel Host Slave Mode Read Cycle for DSPAB
F A1:0 Tmas F DATA7:0
Tmah
Tmdsu Tmdhw F Tmwpw Tmwd Tmrwhld Tmwtrd
F CS
Tmcdw
F R/W
Tmrwsu
F DS
Figure 8. Motorola(R) Parallel Host Slave Mode Write Cycle for DSPAB
15
1.11 Switching Characteristics -- Motorola(R) Host Slave Mode (DSPC)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Unit
Address setup before CS and DS low Address hold time after CS and DS low
Read
Tmas Tmah Tmcdr Tmdd (Note 1) Tmrpw Tmdhr Tmdis (Note 1) (Note 1) Tmrd Tmrdtw Tmcdw Tmdsu (Note 1) Tmwpw Tmrwsu Tmrwhld Tmdhw Tmwtrd Tmwd
DCLKP DCLKP+15 0 2*DCLKP DCLKP+ 10 2*DCLKP+10 2*DCLKP+10 0 2*DCLKP+10 2*DCLKP DCLKP 5 DCLKP 2*DCLKP+10 2*DCLKP+10
2*DCLKP+ 25 2*DCLKP+ 10 -
ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Delay between DS then CS low or CS then DS low Data valid after CS and RD low with R/W high CS and DS low for read Data hold time after CS or DS high after read Data high-Z after CS or DS high low after read CS or DS high to CS and DS low for next read CS or DS high to CS and DS low for next write
Write
Delay between DS then CS low or CS then DS low Data setup before CS or DS high CS and DS low for write R/W setup before CS AND DS low R/W hold time after CS or DS high Data hold after CS or DS high CS or DS high to CS and DS low with R/W high for next read (Note 1) CS or DS high to CS and DS low for next write (Note 1)
Notes: 1. Certain timing parameters are normalized to the DSP clock, DCLKP, in nanoseconds. DCLKP = 1/DCLK. The DSP clock can be defined as follows: Internal Clock Mode: DCLK ~ 60MHz before and during boot, i.e. DCLKP ~ 16.6ns DCLK ~ 86 MHz after boot, i.e. DCLKP ~ 11.6ns It should be noted that DCLK for the internal clock mode is application specific. The application code users guide should be checked to confirm DCLK for the particular application.
16
A1:0 Tmah DATA7:0 CS R/W DS Tmas Tmdd Tmrwsu Tmcdr Tmrpw Tmrd Tmdis Tmrdtw Tmrwhld Tmdhr
Figure 9. Motorola(R) Parallel Host Slave Mode Read Cycle for DSPC
A1:0 Tmas DATA7:0 Tmdsu CS Tmcdw R/W Tmrwsu DS Tmwd Tmwtrd Tmwpw Tmrwhld Tmdhw Tmah
Figure 10. Motorola(R) Parallel Host Slave Mode Write Cycle for DSPC
17
1.12 Switching Characteristics -- SPI Control Port Slave Mode (DSPAB)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Units
FSCCLK clock frequency FCS falling to FSCCLK rising FSCCLK low time FSCCLK high time Setup time FSCDIN to FSCCLK rising Hold time FSCCLK rising to FSCDIN Transition time from FSCCLK to FSCDOUT valid Time from FSCCLK rising to FINTREQ rising Hold time for FINTREQ from FSCCLK rising Time from FSCCLK falling to FCS rising High time between active FCS Time from FCS rising to FSCDOUT high-Z
(Note 1)
fsck tcss tscl tsch
20 150 150 50 50 0 20 200
2 40 200 20
MHz ns ns ns ns ns ns ns ns ns ns ns
(Note 2) (Note 3) (Note 4, 5)
tcdisu tcdih tscdov tscrh tscrl tsccsh tcsht tcscdo
Notes: 1. The specification fsck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the DSP application code. The relevant application code user's manual should be consulted for the software speed limitations. 2. Data must be held for sufficient time to bridge the transition time of FSCCLK. 3. FINTREQ goes high only if there is no data to be read from the DSP at the rising edge of FSCCLK for the second-to-last bit of the last byte of data during a read operation as shown. 4. If FINTREQ goes high as indicated in (Note 3), then FINTREQ is guaranteed to remain high until the next rising edge of FSCCLK. If there is more data to be read at this time, FINTREQ goes active low again. Treat this condition as a new read transaction. Raise chip select to end the current read transaction and then drop it, followed by the 7-bit address and the R/W bit (set to 1 for a read) to start a new read transaction.
18
tsccsh
FCS tcsht tscl
0 2 7 5 6 7 0 6 1
tcss
FSCCLK
t r A6 A5 A0 R/W MSB
t f
tsch
FSCDIN
LSB
A6
t cdisu t cdih
FSCDOUT tscdov
MSB
LSB tri-state tscdov tcscdo
FINTREQ
tscrh
tscrl
Figure 11. SPI Control Port Slave Mode Timing (DSPAB)
19
1.13 Switching Characteristics -- SPI Control Port Slave Mode (DSPC)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Units
SCCLK clock frequency CS falling to SCCLK rising SCCLK low time SCCLK high time Setup time SCDIN to SCCLK rising Hold time SCCLK rising to SCDIN Time from SCCLK low to SCDOUT valid Time from SCCLK rising to INTREQ rising Hold time for INTREQ from SCCLK rising Time from SCCLK falling to CS rising Time from SCCLK low to CS falling High time between active CS Time from CS rising to SCDOUT high-Z
(Note 1)
fsck tcss tscl tsch
4*DCLKP 4*DCLKP 4*DCLKP DCLKP DCLKP+20 DCLKP 2*DCLKP+15 10 4*DCLKP
5 3*DCLKP+20 DCLKP DCLKP
MHz ns ns ns ns ns ns ns ns ns ns ns ns
(Note 2)
tcdisu tcdih tscdov tscrh tscrl tsccsh tsccsl tcsht tcscdo
Notes: 1. The specification fsck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the software. The relevant application code user's manual should be consulted for the software speed limitations. 2. Data must be held for sufficient time to bridge the transition time of SCCLK.
20
Figure 12. SPI Control Port Slave Mode Timing (DSPC)
21
1.14 Switching Characteristics -- Digital Audio Input (DSPAB)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Unit
FSCLKN1 period for Slave mode FSCLKN1 duty cycle for Slave mode
Slave Mode
Tsclki
40 45 10 10 5 5
55 -
ns % ns ns ns ns
(Note 2) Time from active edge of FSCLKN1(2) to FLRCLKN1(2) transition Time from FLRCLKN1(2) transition to FSCLKN1(2) active edge FSDATAN1(2) setup to FSCLKN1(2) transition (Note 1)
Tstlr Tlrts Tsdsus Tsdhs
FSDATAN1(2) hold time after FSCLKN1(2) transition
(Note 1)
Notes: 1. This timing parameter is defined from the active edge of FSCLKN1/2. The active edge of FSCLKN1/2 is the point at which the data is valid. 2. Slave mode is defined as FSCLKN1/2 and FLRCLKN1/2 driven by an external source.
FSC LKN1 FSC LKN2 T sclki T lrts FLRC LKN1 FL R C L K N 2 T s dsu s T sd hs FS D A T A N 1 FSDATAN2 T stlr
Figure 13. Digital Audio Input Data, Slave Clock Timing
22
1.15 Switching Characteristics -- Serial Audio Input (DSPC)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Slave Mode Symbol Min Max Unit
SCLKN period for Slave mode SCLKN duty cycle for Slave mode Time from active edge of SCLKN to LRCLKN transition Time from LRCLKN transition to SCLKN active edge SDATAN0 setup to SCLKN transition SDATAN0 hold time after SCLKN transition (Notes 2) (Notes 2)
Tsclki Tstlr Tlrts Tsdsus Tsdhs
40 45 20 20 10 10
55 -
ns % ns ns ns ns
Notes: 1. Slave mode is defined as SCLKN and LRCLKN being driven by an external source. 2. This timing parameter is defined from the active edge of SCLKN. The active edge of SCLKN is the point at which the data is valid.
SCLKN Tsclki Tlrts LRCLKN Tstlr
Tsdsus
Tsdhs
SDATAN0, 1, 2, 3
Figure 14. Serial Audio Input Data, Slave Clock Timing
23
1.16 Switching Characteristics -- CMPDAT, CMPCLK (DSPAB)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Unit
Serial compressed data clock CMPCLK frequency CMPDAT setup before CMPCLK high CMPDAT hold after CMPCLK high
CMPCLK CMPDAT Tcmpsu Tcmpclk
Tcmpclk Tcmpsu Tcmphld
10 10
27 -
MHz ns ns
Tcmphld
Figure 15. Serial Compressed Data Timing
24
1.17 Switching Characteristics -- Parallel Data Input (DSPAB)
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Unit
CMPCLK Period FDAT[7:0] setup before CMPCLK high FDAT[7:0] hold after CMPCLK high
Tcmpclk Tcmpsu Tcmphld
4*DCLKP + 10 10 10
ns ns ns
Notes: 1. Certain timing parameters are normalized to the DSP clock, DCLK, in nanoseconds. The DSP clock can be defined as follows: Internal Clock Mode: DCLK ~ 60MHz before and during boot, i.e. DCLKP ~ 16.6ns DCLK ~ 86 MHz after boot, i.e. DCLKP ~ 11.6ns It should be noted that DCLK for the internal clock mode is application specific. The application code users guide should be checked to confirm DCLK for the particular application.
CMPCLK FDAT[7:0] Tcm psu Tcmpclk Tcm phld
Figure 16. Parallel Data Timing
25
1.18 Switching Characteristics -- Digital Audio Output
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Symbol Min Max Unit
MCLK period MCLK duty cycle SCLK0, SCLK1 period for Master or Slave mode SCLK0, SCLK1 duty cycle for Master or Slave mode
Master Mode (Output A1 Mode)
Tmclk (Note 2) (Note 2) Tsclk
40 40 40 45
60 55 15 10 10
ns % ns % ns ns ns ns ns ns
(Note 2, 3) SCLK0, SCLK1 delay from MCLK rising edge, MCLK as an input
Tsdmi Tlrds Tadsm Tstlr Tlrts Tadss 10 10
LRCLK0, LRCLK1 delay from SCLK0, SCLK1 transition, respectively (Note 4) AUDATA7-0 delay from SCLK0, SCLK1 transition (Note 4)
Slave Mode (Output A0 Mode)
(Note 5) Time from active edge of SCLK0, SCLK1 to LRCLK0, LRCLK1 transition Time from LRCLK0, LRCLK1 transition to SCLK0, SCLK1 active edge AUDATA7-0 delay from SCLK0, SCLK1 transition (Note 4)
15
Notes: 1. DSPC has two Digital Audio Output modules having analogous signal names ending in 0 and 1. Both DAO ports share a common MCLK but have independent SCLKs and LRCLKs. 2. Master mode timing specifications are characterized, not production tested. 3. Master mode is defined as the CS49400 driving both SCLK0, SCLK1, LRCLK0, and LRCLK1. When MCLK is an input, it is divided to produce SCLK0, SCLK1, LRCLK0 and LRCLK1. 4. This timing parameter is defined from the non-active edge of SCLK0 and SCLK1. The active edge of SCLK0 and SCLK1 is the point at which the data is valid. 5. Slave mode is defined as SCLK0, SCLK1, LRCLK0 and LRCLK1 driven by an external source.
26
MCLK (Input) Tmclk SCLK0,1 (Output) T sdmo,T sdmi SCLK 0,1 (Output) Tsclk Tlrds LRCLK 0,1 (Output) Tadsm AUDATA7:0
Master Mode (Output A1) Output Clock Timing and Digital Audio Output Data
SCLK 0,1 (Input) Tlrts LRCLK 0,1 (Input) Tadss AUDATA7:0 Tsclk Tstlr
Slave Mode (Output A0) Output Clock Timing and Digital Audio Output Data
Figure 18. Digital Audio Output Data, Input and Output Clock Timing
27
1.19 Switching Characteristics -- SRAM/FLASH Interface
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF)
Parameter Write Cycle
Single Byte Write Cycle Data Hold after NV_WE or NV_CS high Data Valid after NV_CS and NV_WE low Data Strobe Twrc Tdh Tdv Tds Trdc Tds Tdh Tsu DCLKP-5 (SRAM_FLASH_RD_CYCLE + 1) * DCLKP DCLKP-5 DCLKP+5 DCLKP+5 (SRAM_FLASH_WR_CYCLE + 1) * DCLKP DCLKP-5
Symbol
Min
Max
Unit
10 -
ns ns ns ns ns ns ns ns
Read Cycle
Single Byte Read Cycle Data Strobe Data Hold after NV_WE or NV_CS high Data Setup Time
XTA[19:0]
NV_CS T wrc NV_WE T dv XTD[7:0] MSP T dh LSP T ds
Figure 19. SRAM/Flash Controller Timing Diagram - Write Cycle
EXTA[19:0]
NV_CS T rdc NV_OE T su EXTD[7:0] MSP Tdh LSP Tds
Figure 20. SRAM/Flash Controller Timing Diagram - Read Cycle
28
EXTA[19:0]
Valid
NV_CS Twrc NV_WE T ds
NV_OE T dv EXTD[7:0] LSP T dh
Figure 21. SRAM/Flash Controller Timing Diagram - Single Byte Write Cycle
EXTA[19:0]
Valid
NV_CS Trdc NV_OE Tds
NV_WE Tsu EXTD[7:0] LSP Tdh
Figure 22. SRAM/Flash Controller Timing Diagram - Single Byte Read Cycle
29
1.20 Switching Characteristics -- SDRAM Interface
(TA = 25 C; VDD, PLLVDD = 2.5 V; VDDSD = 3.3 V; CL = 20 pF, SD_CLKOUT = SD_CLKIN)
Parameter Symbol Min Max Unit
SD_CLKIN high time SD_CLKIN low time SD_CLKOUT rise/fall time SD_CLKOUT duty cycle SD_CLKOUT rising edge to signal valid Signal hold from SD_CLKOUT rising edge SD_CLKOUT rising edge to SD_DQMn valid SD_DQMn hold from SD_CLKOUT rising edge SD_DATA valid setup to SD_CLKIN rising edge SD_DATA valid hold to SD_CLKIN rising edge SD_CLKOUT rising edge to ADDRn valid
tclk_high tclk_low tclkrf tclkrf td th tDQd tDQh tDAs tDAh td
0.475*DCLKP 0.475*DCLKP 45 1.0 1.0
1 55 9.8 7.2 8.3 1.0
ns ns ns % ns ns ns ns ns ns ns
-
8.0
SD _CLK O UT
td
S D _C S
th
S D _R A S
S D _C A S
S D _W E
SD _DQ M n
S D_AD D Rn
O P CO D E
S D_DA TA n
Figure 23. SDRAM Controller Timing Diagram - Load Mode Register Cycle
30
LKOUT
td
th
S D_CS
D_RA S
D_CA S
S D_WE
tDQh
00 11
_DQMn
ADDRn
DATAn
LSP0
MSP0
Figure 24. SDRAM Controller Timing Diagram - Burst Write Cycle
31
32
th tclkrf TDQh
00 11 CAS=2 LSP0 MSP0
_CLKOUT
td
S D_ CS
S D_ RA S
S D_ CA S
S D_ W E
tDQd
SD_DQMn
D_ADDRn
td tDAs tDAh
SD_DATAn
LSP3
MSP3
SD_CLKIN
tclk_low
tclk_high
Figure 25. SDRAM Controller Timing Diagram - Burst Read Cycle
SD_CLKOUT
td SD_CS
td
th
SD_RAS
SD_CAS
SD_WE
SD_DQMn
SD_ADDRn
SD_DATAn
Figure 26. SDRAM Controller Timing Diagram - Auto Refresh Cycle
33
2. OVERVIEW
The CS49400 is a 24-bit fixed-point decoder DSP followed by a 32-bit fixed point programmable post-processor DSP. The decoder portion of the CS49400 is referred to as "DSPAB". The postprocessor DSP is referred to as "DSPC". Both DSPAB and DSPC include their own dedicated peripherals such as serial and parallel control ports, and serial audio interfaces. DSPC also has a external memory interface which supports SRAM/SDRAM/EPROM. All the decoding/processing algorithms listed below require delivery of PCM or IEC61937packed compressed data via I2S or LJ formatted digital audio to the CS49400. Today the CS49400 will support all of the following decoding/processing standards: * PCM Pass-Through/PCM Upsampler * * * * * * * * * * * * * * * * Dolby DigitalTM (with Dolby Pro Logic)TM Dolby Digital Pro Logic IITM Dolby Digital EXTM Dolby Digital EX Pro Logic IITM MPEG-2, Advanced Audio Coding Algorithm (AAC) MPEG Multichannel MPEG Multichannel with Dolby Pro Logic IITM MPEG-1/2, Layer III (MP3) DTS Digital SurroundTM DTS 96/24TM (Front-end Decoder) DTS Digital SurroundTM with Dolby Pro Logic IITM DTS-ES Extended (DTS-ES Discrete 6.1 and DTS-ES Matrix 6.1) DTS-ES 96/24TM (Front-end Decoder) DTS Neo:6TM LOGIC7(R) SRS Circle SurroundTM II SurroundTM
*
HDCD(R)
All of the above audio decoding/processing algorithms and the associated application notes (AN208 and their corresponding appendices) are available through the Crystal WareTM Software Licensing Program. Please refer to AN208 for the latest listing of application codes for DSPAB. DSPC is unique to DSPAB in the sense that the designer may choose to just load a standard or enhanced application code (.ULD file) from the Crystal Ware Software Library or if they have access to the Cirrus Framework DSPC Development Kit, they may choose to build their own application code from a variety of modules. A DSPC application code contains all of the necessary post-processing modules, such as Crossbar Mixer, Pro Logic Module, Bass Manager Module, and Audio Manager (Kernel). A module is just a single processing module, such as Tone Control, Parametric/Graphic EQ, or Dolby Pro Logic matrix decoder. DSPC on the CS49400 will support the following post-processing application codes and/or modules: * Standard Post-Processor (includes the following modules all compiled into one .ULD file): Downmixer module, Dualzone module, Crossbar Mixer module, 7.1 Channel Bass Manager module, Audio Manager module (Volume Control, Trim Control and Channel Remap), and Delay module * Advanced Post-Processor (includes the all of the standard post-processing modules plus the Tone Control module, Parametric EQ module, Re-EQ module in all compiled into one .ULD ) Dolby Pro LogicTM Dolby Pro Logic IITM SRS Circle Surround IITM DTS Neo:6TM LOGIC7(R) THX(R) Surround EXTM 7.1 Channel Post-Processor
* * * * * *
34
* * * * * * * * *
THX(R) Ultra2 CinemaTM 7.1 Channel Post-Processor Cirrus Extra Surround
TM
2.2 DSPC
DSPC is a 32-bit, general-purpose, fixed-point RAM-based processor which includes on-chip ROM tables. It has been designed with a generous amount of on-chip program and data RAM, and has all necessary peripherals required to support the latest standards in consumer entertainment products such as AV receivers and DVDAudio/Video players. DSPC has on-chip data and program RAM, and both external SDRAM and SRAM memory interfaces. These interfaces can be used to expand the data memory. DSPC also has its own 8-channel digital audio input for post-processing PCM from a Multichannel Super Audio CD (SACD) input or DVD-Audio/Video input, via high-performance A/Ds or from some other type of multichannel digital input, capable of delivering 4 stereo digital audio channels such as IEEE1394 (a.k.a. I-Link(R) or Firewire(R)). Data can be delivered to this port using the standard audio formats (I2S or LJ). DSPC can be controlled serially using the SPI standard or via Parallel host control port using the Motorola(R) or Intel(R) standard. DSPC has a Digital Audio output port that has eight stereo serial data outputs for a total of 16 channels. Data can be delivered from these outputs in serial I2S or LJ format. Two of these outputs (AUDAT3, AUDAT7) can be configured as a IEC60958-format S/PDIF transmitter. This document focuses on the electrical features of the CS49400. The features are described from a hardware design perspective. It should be understood that not all of the features portrayed in this document are supported by all of the versions of application code available. The application code user's guides should be consulted to determine which hardware features are supported by the software. Please note that a download of application software is required each time the part is powered up. This term should be interpreted as meaning the transfer of application code into the internal memory of the part
Cirrus Original Multichannel SurroundTM Virtual Dolby DigitalTM/Virtual Dolby Digital Pro Logic IITM Virtualizer Module VMAx VirtualTheaterTM Virtualizer Module HDCD(R) Multichannel Decoder DVD-Audio/Video and Multichannel SACD Bass Management DTS/DTS-ES 96/24TM Back-End Decoder DTS/DTS-ES 96/24TM Back-End Decoder with THX(R) Ultra2 CinemaTM
All of the above audio post-processing applications codes and/or Cirrus FrameworkTM modules and the associated application notes (AN209 and the associated appendices) are available through the Crystal WareTM Software Licensing Program. All standard or enhanced post-processing code modules are only available to customers who qualify for the Cirrus FrameworkTM CS49400 Family DSPC Programming Kit. Please refer to AN209 for the latest listing of application codes and Cirrus FrameworkTM modules available for DSPC.
2.1 DSPAB
DSPAB is an enhanced version of the CS49300. It was designed to have legacy code support for all decoder applications developed for the CS49300. It includes performance enhancements such as the ability to decode AAC without the need for external SRAM memory. DSPAB has a Digital Audio Input (DAI) and a Compressed Data Input (CDI) port for data delivery in either I2S or LJ format. DSPAB can be controlled serially using the SPI standard and can also be controlled via a Parallel host control port using the Motorola(R) or Intel(R) communication standards.
35
from either an external microcontroller or through one of the boot procedures listed in Section 8.
3.2 Termination Requirements
The CS49400 incorporates open drain pins which must be pulled high for proper operation. FINTREQ and INTREQ are always open drains which requires a pull-up for proper operation. Due to the internal, multiplexed design of the pins, certain signals may or may not require termination depending on the mode being used. If a parallel host communication mode is not being used, all parallel control pins must be terminated or driven as these pins will come up as high impedance inputs and will be prone to oscillation if they are left floating. The specific termination requirements may vary since the state of some of the GPIO pins will determine the communication mode at the rising edge of reset (please see Section 6 "Control" on page 41 for more information). For the explicit termination requirements of each communication mode please see the typical connection diagrams. Generally a 3.3k Ohm resistor is recommended for open drain and mode select pins. A 10k Ohm resistor is sufficient for all other unused inputs.
3. TYPICAL CONNECTION DIAGRAMS
Four typical connection diagrams have been presented to illustrate using the part with the different communication modes available. They are as follows: Figure 27, "SPI Control with External Memory 144 Pin Package" on page 38. Figure 28, "Intel(R) Parallel Control Mode - 144 Pin Package" on page 39. Figure 29, "Motorola(R) Parallel Control Mode - 144 Pin Package" on page 40. The following should be noted when viewing the typical connection diagrams:
Note: The pins are grouped functionally in each of the typical connection diagrams. Please be aware that the CS49400 symbol may appear differently in each diagram.
The external memory interface is supported when a serial or parallel communication mode has been chosen.
3.1 Multiplexed Pins
The CS49400 incorporates a large amount of flexibility into a 144 pin package. The pins are internally multiplexed to serve multiple purposes. Some pins are designed to operate in one mode at power up, and serve a different purpose when the DSP is running. Other pins have functionality which can be controlled by the application running on the DSP. In order to better explain the behavior of the part, the pins which are multiplexed have been given multiple names. Each name is specific to the pin's operation in a particular mode. In this document, pins will be referred to by their functionality. Section 12 "Pin Description" on page 86 describes each pin of the CS49400 and lists all of its names. Please refer to this section when exact pin numbers are in question.
3.3 Phase Locked Loop Filter
The internal phase locked loop (PLL) of the CS49400 requires an external filter. The topology of this filter is shown in the typical connection diagrams. The component values are shown below. Care should be taken when laying out the filter circuitry to minimize trace lengths and to avoid any high frequency signals. Any noise coupled onto the filter circuit will be directly coupled into the PLL, which could affect performance.
Reference Designator Value
C1 C2 C3 R1
2.2uF 1200pF 68pF 3k Ohm
Table 1. PLL Filter Component Values
36
4. POWER
The CS49400 requires a 2.5V digital power supply for the core logic and 2.5V I/O and a 2.5V analog power supply for the internal PLL. For systems with external memory that runs on 3.3V, a 3.3V digital power supply is required on the VDDSD pins along with four digital grounds on VSSSD. There are seven digital power pins, VDD1 through VDD7, along with seven digital grounds, VSS1 through VSS7. There is one analog power pin, PLLVDD, and one analog ground, PLLVSS. The recommendations given below for decoupling and power conditioning of the CS49400 will help to ensure reliable performance.
4.2 Analog Power Conditioning
In order to obtain the best performance from the CS49400's internal PLL, the analog power supply PLLVDD must be as noise-free as possible. A ferrite bead and two capacitors should be used to filter the VDD to generate PLLVDD. This power scheme is shown in the typical connection diagrams.
4.3 Ground
For two layer circuit boards, care should be taken to have sufficient ground between the DSP and parts in which it will be interfacing (DACs, ADCs, S/PDIF Receivers, microcontrollers, and especially external memory). Insufficient ground can degrade noise margins between devices resulting in data integrity problems.
4.1 Decoupling
It is necessary to decouple the power supply by placing capacitors directly between the power and ground of the CS49400. Each pair of power/ground pins (VDD1/VSS1, etc.) should have its own decoupling capacitors. The recommended procedure is to place both a 0.1uF and a 1uF capacitor as close as physically possible to each power pin. The 0.1uF capacitor should be closest to the part (typically 5mm or closer).
4.4 Pads
The CS49400 has two different I/O voltage levels. All signal pins not associated with the External SRAM/SDRAM memory interface operate from the 2.5V supply and are 3.3V tolerant. The external SRAM/SDRAM memory interface operates at 3.3V only. However, if the external memory interface is not used VDDSD1-4 may be connected to 2.5V.
37
NOTE : 1. A capacitor pair (.01uF and 0.1uF) must be supplied for each power pin. 2. The digital supply (+2.5 VD) is filtered. to obtain the analog suply (+2.5 VA).
+2.5 VD + RESISTOR PACK. 1 3.3K C 10K 10 9 8 7 6 5 4 3 2 + 10K 90 100 114 132 138 10 20 1uF 70 58 51 42 0.1uF 144 3 135 142 136 140 16 15 6 4 7 129 141 120 121 139 130 116 115 112 105 103 97 96 95 12 13 29 27 24 22 19 18 14 9 99 117 111 118 119 134 131 85 86 82 81 80 79 +2.5 VA + C1 127 126 125 123 124 128 122 143 2 1 5 8 VDDSD1 VDDSD2 VDDSD3 VDDSD4 VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 VDD7 RESET INTREQ,ABOOT SCS SCCLK SCDIN SCDOUT,SCDIO SD_CS SD_CLK_EN SD_CLK_IN SD_CLK_OUT SD_DQM0 SD_DQM1 SD_CAS SD_RAS SD_WE NV_CS,GPIO14 NV_OE,GPIO15 NV_WE,GPIO16 SD_ADDR0, EXTA0 SD_ADDR1, EXTA1 SD_ADDR2,EXTA2 SD_ADDR3,EXTA3 SD_ADDR4,EXTA4 SD_ADDR5,EXTA5 SD_ADDR6,EXTA6 SD_ADDR7,EXTA7 SD_ADDR8, EXTA8 SD_ADDR9,EXTA9 SD_ADR10,EXTA10 SD_DATA8,EXTA11 SD_DATA9,EXTA12 SD_DATA10,EXTA13 SD_DATA11,EXTA14 SD_DATA12, EXTA15 SD_DATA13,EXTA16 SD_DATA14,EXTA17 SD_DATA15,EXTA18 SD_BA,EXTA19 SD_DAT0,EXTD0 SD_DAT1,EXTD1 SD_DAT2, EXTD2 SD_DATA3, EXTD3 SD_DATA4,EXTD4 SD_DATA5,EXTD5 SD_DATA6,EXTD6 SD_DATA7,EXTD7 68 64 61 59 39 45 78 77 33 32 31 30 73 74 75 76 67 66 65 63 62 60 72 56 55 54 53 52 49 47 46 71 34 35 36 37 38 40 43 44 RESISTOR PACK. 1uF 0.1uF 47uF 0.1uF 0.01uF 0.1uF FERRITE BEAD +2.5 VA +3.3VD
MICROCONTROLLER
SPI INTERFACE
FINTREQ FCS FAO,FSCCLK FA1, FSCDIN FHS2,FSCDIO,FSCDOUT CS,GPIO9 HINBSY,GPIO8 WR,DS,GPIO10 RD,R/W,GPIO11 A1,GPIO12 AO,GPIO13 HDATA0,GPIO0 HDATA1,GPIO1 HDATA2,GPIO2 HDATA3,GPIO3 HDATA4,GPIO4 HDATA5, GPIO5 HDATA6,GPIO6 HDATA7,GPIO7 FHS0,FWR,FDS FHS1,FRD,FR/ W FDAT0 FDAT1 FDAT2 FDAT3 FDAT4 FDAT5 FDAT6 FDAT7 MCLK CMPREQ,FLRCLKN2 CMPCLK,FSCLKN2 CMPDAT,FSDATAN2 FLRCLKN1 FSCLKN1,STCCLK2 FSDATAN1 LRCLKN, GPIO23 SCLKN,GPIO22 SDATAN0,GPIO24 SDATAN1,GPIO25 SDATAN2,GPIO26 SDATAN3,GPIO27 CLKIN,XTALI CLKOUT,XTAL0 PLLVDD FILT2 FILT1 CLKSEL PLLVSS USH2,CS_OUT,GPIO17 UHS1,GPIO19 UHS0,GPIO18 GPIO20 GPIO21 NC1 NC2 NC3 NC4 NC5
+3.3VD
CS494XX
EXTERNAL ROM
ADC OR SPDIF RX ADC
ADCs OSCILLATOR
SCLK0 LRCLK0 AUDATA0 AUDATA1 AUDATA2 AUDAT3,XMT958A SCLK1 LRCLK1 AUDATA4,GPIO28 AUDATA5,GPIO29 AUDATA6,GPIO30 AUDATA7,XMT958B,GPIO31 TEST DBCK DBDA FDBDA FDBCK VSSSD1 VSSSD2 VSSSD3 VSSSD4 VSS1 VSS2 VSS3 VSS4 VSS5 VSS6 VSS7
104 108 110 109 107 106 98 87 102 94 93 92 28 26 25 23 17 2 3 4 5 6 7 8 9 10
6 DACs 2 SPDIF TX
R1 C2 C3
3.3K C +2.5 VD 1
91 101 113 133 137 11 21
89 88 84 83 48
3.3K
3.3K
10K
10K
Figure 27. SPI Control with External Memory - 144 Pin Package
38
69 57 50 41
NOTE : 1. A capacitor pair (.01uF and 0.1uF) must be supplied for each power pin. 2. The digital supply (+2.5 VD) is filtered. to obtain the analog suply (+2.5 VA).
+2.5 VD + 1 3.3K C 3.3K 10 9 8 7 6 5 4 3 2 + 10K 90 100 114 132 138 10 20 1uF 70 58 51 42 0.1uF 144 135 142 136 140 7 3 129 141 120 121 130 139 116 115 112 105 103 97 96 95 16 15 12 13 6 4 29 27 24 22 19 18 14 9 99 117 111 118 119 134 131 85 86 82 81 80 79 +2.5 VA + C1 127 126 125 123 124 128 122 143 2 1 5 8 VDDSD1 VDDSD2 VDDSD3 VDDSD4 VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 VDD7 RESET SCS SCCLK SCDIN SCDOUT,SCDIO FHS2,FSCDIO,FSCDOUT INTREQ,ABOOT CS,GPIO9 HINBSY,GPIO8 WR,DS,GPIO10 RD,R/W,GPIO11 AO,GPIO13 A1,GPIO12 HDATA0,GPIO0 HDATA1,GPIO1 HDATA2,GPIO2 HDATA3,GPIO3 HDATA4,GPIO4 HDATA5,GPIO5 HDATA6,GPIO6 HDATA7,GPIO7 FINTREQ FCS FHS0,FWR,FDS FHS1,FRD,FR/ W FAO,FSCCLK FA1, FSCDIN FDAT0 FDAT1 FDAT2 FDAT3 FDAT4 FDAT5 FDAT6 FDAT7 MCLK CMPREQ,FLRCLKN2 CMPCLK,FSCLKN2 CMPDAT,FSDATAN2 FLRCLKN1 FSCLKN1,STCCLK2 FSDATAN1 LRCLKN,GPIO23 SCLKN,GPIO22 SDATAN0,GPIO24 SDATAN1,GPIO25 SDATAN2,GPIO26 SDATAN3,GPIO27 CLKIN,XTALI CLKOUT,XTAL0 PLLVDD FILT2 FILT1 CLKSEL PLLVSS USH2,CS_OUT,GPIO17 UHS1,GPIO19 UHS0,GPIO18 GPIO20 GPIO21 NC1 NC2 NC3 NC4 NC5 SCLK0 LRCLK0 AUDATA0 AUDATA1 AUDATA2 AUDAT3,XMT958A SCLK1 LRCLK1 AUDATA4,GPIO28 AUDATA5,GPIO29 AUDATA6,GPIO30 AUDATA7,XMT958B,GPIO31 TEST DBCK DBDA FDBDA FDBCK VSSSD1 VSSSD2 VSSSD3 VSSSD4 VSS1 VSS2 VSS3 VSS4 VSS5 VSS6 VSS7 SD_CS SD_CLK_EN SD_CLK_IN SD_CLK_OUT SD_DQM0 SD_DQM1 SD_CAS SD_RAS SD_WE NV_CS,GPIO14 NV_OE,GPIO15 NV_WE,GPIO16 SD_ADDR0, EXTA0 SD_ADDR1, EXTA1 SD_ADDR2,EXTA2 SD_ADDR3,EXTA3 SD_ADDR4,EXTA4 SD_ADDR5,EXTA5 SD_ADDR6,EXTA6 SD_ADDR7,EXTA7 SD_ADDR8, EXTA8 SD_ADDR9,EXTA9 SD_ADR10,EXTA10 SD_DATA8,EXTA11 SD_DATA9,EXTA12 SD_DATA10,EXTA13 SD_DATA11,EXTA14 SD_DATA12, EXTA15 SD_DATA13,EXTA16 SD_DATA14,EXTA17 SD_DATA15,EXTA18 SD_BA,EXTA19 SD_DAT0,EXTD0 SD_DAT1,EXTD1 SD_DAT2, EXTD2 SD_DATA3, EXTD3 SD_DATA4,EXTD4 SD_DATA5,EXTD5 SD_DATA6,EXTD6 SD_DATA7,EXTD7 68 64 61 59 39 45 78 77 33 32 31 30 73 74 75 76 67 66 65 63 62 60 72 56 55 54 53 52 49 47 46 71 34 35 36 37 38 40 43 44 1uF 0.1uF 47uF 0.1uF 0.01uF 0.1uF FERRITE BEAD +2.5 VA +3.3VD
MICROCONTROLLER
PARALLEL INTERFACE
+3.3VD
CS494XX
EXTERNAL ROM
ADC OR SPDIF RX ADC
ADCs OSCILLATOR
104 108 110 109 107 106 98 87 102 94 93 92 28 26 25 23 17 2 3 4 5 6 7 8 9 10
6 DACs 2 SPDIF TX
R1 C2 C3
3.3K C +2.5 VD 1
91 101 113 133 137 11 21
89 88 84 83 48
Figure 28. Intel(R) Parallel Control Mode - 144 Pin Package
69 57 50 41
3.3K
3.3K
10K
10K
39
NOTE : 1. A capacitor pair (.01uF and 0.1uF) must be supplied for each power pin. 2. The digital supply (+2.5 VD) is filtered. to obtain the analog suply (+2.5 VA).
+2.5 VD + 1 1 3.3K C 10 9 8 7 6 5 4 3 2 10K C + 10K 90 100 114 132 138 10 20 1uF 70 58 51 42 0.1uF 144 135 142 136 140 7 3 129 141 120 121 130 139 116 115 112 105 103 97 96 95 16 15 12 13 6 4 29 27 24 22 19 18 14 9 99 117 111 118 119 134 131 85 86 82 81 80 79 +2.5 VA + C1 127 126 125 123 124 128 122 143 2 1 5 8 VDDSD1 VDDSD2 VDDSD3 VDDSD4 VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 VDD7 RESET SCS SCCLK SCDIN SCDOUT,SCDIO FHS2,FSCDIO,FSCDOUT INTREQ,ABOOT CS,GPIO9 HINBSY,GPIO8 WR,DS,GPIO10 RD,R/W,GPIO11 AO,GPIO13 A1,GPIO12 HDATA0,GPIO0 HDATA1,GPIO1 HDATA2,GPIO2 HDATA3,GPIO3 HDATA4,GPIO4 HDATA5,GPIO5 HDATA6,GPIO6 HDATA7,GPIO7 FINTREQ FCS FHS0,FWR,FDS FHS1,FRD,FR/ W FAO,FSCCLK FA1, FSCDIN FDAT0 FDAT1 FDAT2 FDAT3 FDAT4 FDAT5 FDAT6 FDAT7 MCLK CMPREQ,FLRCLKN2 CMPCLK,FSCLKN2 CMPDAT,FSDATAN2 FLRCLKN1 FSCLKN1,STCCLK2 FSDATAN1 LRCLKN,GPIO23 SCLKN,GPIO22 SDATAN0,GPIO24 SDATAN1,GPIO25 SDATAN2,GPIO26 SDATAN3,GPIO27 CLKIN,XTALI CLKOUT,XTAL0 PLLVDD FILT2 FILT1 CLKSEL PLLVSS USH2,CS_OUT,GPIO17 UHS1,GPIO19 UHS0,GPIO18 GPIO20 GPIO21 NC1 NC2 NC3 NC4 NC5 SCLK0 LRCLK0 AUDATA0 AUDATA1 AUDATA2 AUDAT3,XMT958A SCLK1 LRCLK1 AUDATA4,GPIO28 AUDATA5,GPIO29 AUDATA6,GPIO30 AUDATA7,XMT958B,GPIO31 TEST DBCK DBDA FDBDA FDBCK VSSSD1 VSSSD2 VSSSD3 VSSSD4 VSS1 VSS2 VSS3 VSS4 VSS5 VSS6 VSS7 SD_CS SD_CLK_EN SD_CLK_IN SD_CLK_OUT SD_DQM0 SD_DQM1 SD_CAS SD_RAS SD_WE NV_CS,GPIO14 NV_OE,GPIO15 NV_WE,GPIO16 SD_ADDR0, EXTA0 SD_ADDR1, EXTA1 SD_ADDR2,EXTA2 SD_ADDR3,EXTA3 SD_ADDR4,EXTA4 SD_ADDR5,EXTA5 SD_ADDR6,EXTA6 SD_ADDR7,EXTA7 SD_ADDR8, EXTA8 SD_ADDR9,EXTA9 SD_ADR10,EXTA10 SD_DATA8,EXTA11 SD_DATA9,EXTA12 SD_DATA10,EXTA13 SD_DATA11,EXTA14 SD_DATA12, EXTA15 SD_DATA13,EXTA16 SD_DATA14,EXTA17 SD_DATA15,EXTA18 SD_BA,EXTA19 SD_DAT0,EXTD0 SD_DAT1,EXTD1 SD_DAT2, EXTD2 SD_DATA3, EXTD3 SD_DATA4,EXTD4 SD_DATA5,EXTD5 SD_DATA6,EXTD6 SD_DATA7,EXTD7 68 64 61 59 39 45 78 77 33 32 31 30 73 74 75 76 67 66 65 63 62 60 72 56 55 54 53 52 49 47 46 71 34 35 36 37 38 40 43 44 RESISTOR PACK. 10 9 8 7 6 5 4 3 2 1uF 0.1uF 47uF 0.1uF 0.01uF 0.1uF FERRITE BEAD +2.5 VA +3.3VD
MICROCONTROLLER
PARALLEL INTERFACE
+3.3VD
CS494XX
EXTERNAL ROM
ADC OR SPDIF RX ADC
ADCs OSCILLATOR
104 108 110 109 107 106 98 87 102 94 93 92 28 26 25 23 17 2 3 4 5 6 7 8 9 10
6 DACs 2 SPDIF TX
R1 C2 C3
3.3K C +2.5 VD 1
91 101 113 133 137 11 21
89 88 84 83 48
10K
10K
Figure 29. Motorola(R) Parallel Control Mode - 144 Pin Package
40
69 57 50 41
5. CLOCKING
The CS49400 clock manager incorporates a programmable phase locked loop (PLL) clock synthesizer. The PLL takes an input reference clock and produces all the clocks required to run the DSP and peripherals. In A/V Receiver designs, the CLKIN pin is typically connected to a 12.288MHz oscillator. The clock manager is controlled by the DSPAB application software. The software user's guide for the application code being used should be referenced for which CLKIN input frequency is supported.
UHS2 (Pin 143) 1 1
144-Pin Package UHS0 Host Interface Mode UHS1 (Pin 1) (Pin 2) 0 1 Serial SPI 1 0 8-bit Intel(R)
1
UHS2 (Pin 99) 1
8-bit Motorola(R) 100-Pin Package UHS0 Host Interface Mode UHS1 (Pin 1) (Pin 2) 0 1 Serial SPI
Table 3. Host Modes for DSPC
1
1
6. CONTROL
Control of the CS49400 can be accomplished through one of three methods. The CS49400 supports SPI serial communication and Motorola(R) and Intel(R) byte-wide parallel communication. Both DSPAB and DSPC have their own control ports. Only one of the three communication modes can be selected for control. Both DSPAB and DSPC use the same communication mode. However, please note that the 100-pin package only supports SPI serial communication. The states of the FHS[2:0] for DSPAB and UHS[2:0] for DSPC, sampled at the rising edge of RESET, determine the communication interface (Table 2.)
FHS2 (Pin 7) 1 1 144-Pin Package Host Interface Mode FHS0 FHS1 (Pin 13) (Pin 12) 0 1 Serial SPI 1 0 8-bit Intel(R)
Whichever host communication mode is used, host control of the CS49400 is handled through the application software running on the DSP. Configuration and control of the CS49400 decoder and its peripherals are indirectly executed through a messaging protocol supported by the downloaded application code. In other words, successful communication can only be accomplished by following the low level hardware communication format and high level messaging protocol. The specifications of the messaging protocol can be found in any of the software user's guides, such as AN208 and AN209. The system designer only needs to read the subsection describing the communication mode being used. Please note that the communication protocol might be slightly different for DSPAB and DSPC. The following sections will explain each communication mode in more detail. Flow diagrams will illustrate read and write cycles. The timing diagrams shown demonstrate relative edge positions of signal transitions for read and write operations.
1
FHS2 (Pin 6) 1
8-bit Motorola 100-Pin Package Host Interface Mode FHS0 FHS1 (Pin 10) (Pin 9) 0 1 Serial SPI
Table 2. Host Modes for DSPAB
1
1
(R)
6.1 Serial Communication 6.1.1 SPI Communication for DSPAB
SPI communication with DSPAB is accomplished with five communication lines: chip select, serial control clock, serial data in, serial data out, and an interrupt request line that signals DSPAB has data to transmit to the host. Table 4 lists the mnemonic,
.
41
pin name, and pin number of each of these signals on DSPAB.
Mnemonic Pin Name 144-Pin Package, Pin Number 15 6 4 7 100-Pin Package, Pin Number 11 5 4 6
Chip Select FCS Serial Clock FSCCLK Serial Data In FSCDIN Serial Data Out FSCDOUT Interrupt Request FINTREQ
for DSPAB defaults to 1000000b. It is necessary to clock this address in prior to any transfer in order for DSPAB to accept the write. In other words a byte of 0x80 should be clocked into the device preceding any write. The 0x80 byte represents the 7-bit address 1000000b, with the least significant bit set to 0 to designate a write. 3) The host should then clock data into the device most significant bit first, one byte at a time. The data byte is transferred from the shift register to the DSP input register on the falling edge of the eighth serial clock. For this reason, the serial clock should default to low so that eight transitions from low to high to low will occur for each byte. A 32 S byte to byte latency must be obeyed during run time. 4) When all of the bytes have been transferred, chip select should be raised to signify an end of write. Once again it is crucial that the serial clock transitions from high to low on the last bit of the last byte before chip select is raised, or a loss of data will occur. The same write routine could be used to send a single byte, a message, or an entire application code image. From a hardware perspective, it makes no difference whether communication is by byte or multiple bytes of any length as long as the correct hardware protocol is followed.
16
12
Table 4. SPI Communication Signals for DSPAB
6.1.1.1 Writing in SPI for DSPAB
When writing to the device in SPI the same protocol will be used whether writing a byte, a message, or even an entire executable download image. The examples shown in this document can be expanded to fit any write situation. Figure 30, "SPI Write Flow Diagram for DSPAB" on page 42 shows a typical write sequence:
SPI START: FCS (LO W )
W RIT E ADDRESS BYTE W ITH MODE BIT SET TO 0 F OR W RITE
W RIT E DATA BY TE
Y MORE DATA? N SPI STO P: FCS (HIGH)
6.1.1.2 Reading in SPI for DSPAB
A read operation is necessary when DSPAB signals that it has data to be read. DSPAB does this by dropping its interrupt request line (FINTREQ) low. When reading from the device in SPI, the same protocol will be used whether reading a single byte or multiple bytes. The examples shown in this document can be expanded to fit any read situation. Figure 32, "SPI Read Flow Diagram for DSPAB" on page 44 shows a typical read sequence: The following is a detailed description of an SPI read sequence with DSPAB.
Figure 30. SPI Write Flow Diagram for DSPAB
The following is a detailed description of an SPI write sequence with DSPAB. 1) An SPI transfer is initiated when chip select (FCS) is driven low. 2) This is followed by a 7-bit address and the read/write bit set low for a write. The address
42
F SCCLK
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
FSCDIN
AD6 AD5 AD4 AD3 AD2 AD1 AD0 R/W
F CS
S PI W rite Functional Tim ing
F SCCLK
F SCDIN
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5
AD6 AD5 AD4 AD3 AD2 AD1 AD0 R/W D4 D3 D2 D1 D0
F SCDOUT
F CS
F INTREQ
SPI Read Functional Tim ing
Note 1
Note 2
Notes: 1. FINTREQ is guaranteed to stay LOW until the rising edge of FSCCLK for bit D1 of the last byte to be transferred out of the CS49400. 2. FINTREQ is guaranteed to remain HIGH until the next rising edge of FSCCLK at which point it may go LOW again if there is new data to be read. The condition of FINTREQ going LOW at this point should be treated as a new read condition. After a stop condition, a new start condition and an address byte should be sent
Figure 31. SPI Timing for DSPAB
43
to designate a read. 4) After the falling edge of the serial control clock (FSCCLK) for the read/write bit, the data is ready to be clocked out on the control data out pin (FCDOUT). Data clocked out by the host is valid on the rising edge of FSCCLK. Data transitions occur on the falling edge of FSCCLK. The serial clock should be default low so that eight transitions from low to high to low will occur for each byte. 5) If FINTREQ is still low, another byte should be clocked out of DSPAB. Please see the discussion below for a complete description of FINTREQ behavior. 6) When FINTREQ is released, the chip select line of DSPAB should be taken high to end the read transaction.
Y
FINTREQ (LOW )? Y FCS LOW
N
W RITE ADD RES S BYTE W ITH MODE BIT SET TO 1 FOR READ
READ DA TA BYTE
FINTRE Q STILL LO W ?
N FCS HIGH
Figure 32. SPI Read Flow Diagram for DSPAB
1) An SPI read transaction is initiated by DSPAB dropping FINTREQ, signaling that it has data to be read. 2) The host responds by driving chip select (FCS) low. 3) This is followed by a 7-bit address and the read/write bit set high for a read. The address for DSPAB defaults to 1000000b. It is necessary to clock this address in prior to any transfer in order for DSPAB to acknowledge the read. In other words a byte of 0x81 should be clocked into the device preceding any read. The 0x81 byte represents the 7-bit address 1000000b, and the least significant bit set to 1
Understanding the role of FINTREQ is important for successful communication. FINTREQ is guaranteed to remain low (once it has gone low) until the second to last rising edge of FSCCLK of the last byte to be transferred out of DSPAB. If there is no more data to be transferred, FINTREQ will go high at this point. For SPI this is the rising edge for the second to last bit of the last byte to be transferred. After going high, FINTREQ is guaranteed to stay high until the next rising edge of FSCCLK. This end of transfer condition signals the host to end the read transaction by clocking the last data bit out and raising FCS. If FINTREQ is still low after the second to last rising edge of FSCCLK, the host should continue reading data from the serial control port. It should be noted that all data should be read out of the serial control port during one transaction or a loss of data will occur. In other words, all data should be read out of the chip until FINTREQ signals the last byte by going high as described above. Please see Section 6.1.3 "FINTREQ Behavior: A Special Case" on page 48 for a more detailed description of FINTREQ behavior.
44
Figure 31, "SPI Timing for DSPAB" on page 43 timing diagram shows the relative edges of the control lines for an SPI read and write.
SPI START: SCS (LOW)
6.1.2 SPI Communication for DSPC
SPI communication with the DSPC is accomplished with five communication lines: chip select, serial control clock, serial data in, serial data out, and an interrupt request line that signals DSPC has data to transmit to the host. Table 5 lists the mnemonic, pin name, and pin number of each of these signals on DSPC.
Mnemonic Pin Name 144-Pin Package, Pin Number 135 142 136 140 141 100-Pin Package, Pin Number 93 98 94 97 N/A
WRITE ADDRESS BYTE WITH MODE BIT SET TO 0 FOR WRITE
WRITE 4 DATA BYTES
Y MORE DATA? N SPI STOP: SCS (HIGH)
HINBSY (HIGH)? Y
N
Figure 33. SPI Write Flow Diagram for DSPC
Chip Select Serial Clock Serial Data In Serial Data Out Host Busy Interrupt Request
SCS SCCLK SCDIN SCDOUT HINBSY INTREQ
1) An SPI transfer is initiated when chip select (SCS) is driven low. 2) This is followed by a 7-bit address and the read/write bit set low for a write. The address for DSPC defaults to 1000001b. It is necessary to clock in this address prior to any transfer in order for DSPC to accept the write. In other words a byte of 0x82 should be clocked into the device preceding any write. The 0x82 byte represents the 7-bit address 1000001b, and the least significant bit set to 0 to designate a write. 3) The host should then clock data into the device most significant bit first, four bytes at a time. The data byte is transferred to the DSP on the falling edge of the eighth serial clock. For this
3
3
Table 5. SPI Communication Signals for DSPC
6.1.2.1 Writing in SPI for DSPC
When writing to the device in SPI the same protocol will be used whether writing a byte, a message or even an entire executable download image. The examples shown in this document can be expanded to fit any write situation. Figure 33, "SPI Write Flow Diagram for DSPC" on page 45 shows a typical write sequence The following is a detailed description of an SPI write sequence with DSPC.
45
reason, the serial clock should default to low so that eight transitions from low to high to low will occur for each byte. 4) When all 4 data bytes have been transferred, chip select should be raised to signify an end of write. Once again it is crucial that the serial clock transitions from high to low on the last bit of the last byte before chip select is raised, or a loss of data will occur. 5) If more data needs to be sent, the host must verify that the HINBSY pin is low before it sends more data to DSPC. Note the HINBSY pin is available only on the 144 pin devices. A 32 S byte to byte latency must be obeyed during run time for the 100 pin devices. The same write routine could be used to send a 4byte message or an entire application code image. From a hardware perspective, communication must be in 4-byte multiples.
N INTREQ (LO W )?
Y SCS LO W
W RITE ADD RESS BYTE W ITH MODE BIT S ET TO 1 FOR RE AD
REA D 4 DA TA BYTES
Y INTREQ STILL LOW ?
6.1.2.2 Reading in SPI for DSPC
A read operation is necessary when DSPC signals that it has data to be read. DSPC does this by dropping its interrupt request line (INTREQ) low. When reading from the device in SPI, the same protocol will be used whether reading a single byte or multiple bytes. The examples shown in this document can be expanded to fit any read situation. Figure 35, "SPI Read Flow Diagram for DSPC" on page 46 shows a typical read sequence: The following is a detailed description of an SPI read sequence with DSPC. 1) An SPI read transaction is initiated by DSPC dropping INTREQ, signaling that it has data to be read. 2) The host responds by driving chip select (SCS) low. 3) This is followed by a 7-bit address and the read/write bit set high for a read. The address for DSPC defaults to 1000001b. It is necessary to clock this address in prior to any transfer in
N SCS HIGH
Figure 35. SPI Read Flow Diagram for DSPC
order for DSPC to acknowledge the read. In other words a byte of 0x83 should be clocked into the device preceding any read. The 0x83 byte represents the 7 bit address 1000001b, and the least significant bit set to 1 designates a read. 4) After the falling edge of the serial control clock (SCCLK) for the read/write bit, the data is ready to be clocked out on the control data out pin (CDOUT). Data clocked out by the host is valid on the rising edge of SCCLK and data transitions occur on the falling edge of SCCLK. The serial clock should default to low so that eight transitions from low to high to low will occur for each byte.
46
SCCLK
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 7 D6 D5 D4 D3 D2 D6 D5 D4 D3 D2 D1 D0 D1 D0
SCDIN
AD 6 AD 5 A D4 AD 3 AD 2 AD 1 AD 0 R/W
S CS
S P I W rite F u n c tio n a l T im ing
SCCLK
SCDIN
D7 D7 D6 D5 D4 D3 D2 D1 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D0
AD 6 AD 5 A D 4
AD 3 A D2 AD 1 AD 0 R /W D7 D6 D5 D4 D3 D2 D1 D0
SCDOUT
S CS
INTREQ
S P I R e a d F u n c tio n a l T im in g
Note 1
Note 2
Notes: 1. INTREQ is guaranteed to stay LOW until the rising edge of SCCLK for bit D1 of the last byte to be transferred out of DSPC. 2. INTREQ is guaranteed to remain HIGH until the next rising edge of SCCLK at which point it may go LOW again if there is new data to be read. The condition of INTREQ going LOW at this point should be treated as a new read condition. After a stop condition, a new start condition and an address byte should be sent
Figure 34. SPI Timing for DSPC
47
5) If INTREQ is still low after 4 bytes, another 4 bytes should be clocked out of DSPC. 6) When INTREQ is released, the chip select line of DSPC should be taken high to end the read transaction. All messages read back from DSPC will be in 4byte multiples.
high for one period of FSCCLK and then goes low again before the end of the read cycle. In case (1) the host should perform a read operation as discussed in the previous sections. In case (2) an unsolicited message arrives before the second to last FSCCLK of the final byte transfer of a read, forcing the FINTREQ pin to remain low. In this scenario the host should continue to read from DSPAB without a stop/start condition or data will be lost. In case (3) an unsolicited message arrives between the second to last FSCCLK and the last FSCCLK of the final byte transfer of a read. In this scenario, FINTREQ will transition high for one clock (as if the read transaction has ended), and then back low (indicating that more data has queued). This final case is the most complicated and shall be explained in detail. There are two constraints which completely characterize the behavior of the FINTREQ pin during a read. The first constraint is that the FINTREQ pin is guaranteed to remain low until the second to last FSCCLK (FSCCLK number N-1) of the final byte being transferred from DSPAB (not necessarily the second to last bit of the data byte). The second constraint is that once the FINTREQ pin has gone high it is guaranteed to remain high until the rising edge of the last FSCCLK (FSCCLK number N) of the final byte being transferred from DSPAB (not necessarily the last bit of the data byte). If an unsolicited message arrives in the window of time between the rising edge of the second to last FSCCLK and the final FSCCLK, FINTREQ will drop low on the rising edge of the final FSCCLK as illustrated in the functional timing diagram shown for the SPI read cycle. FINTREQ behavior for SPI communication is illustrated in Figure 31, "SPI Timing for DSPAB" on page 43. When using SPI communication, the FINTREQ pin will remain low until the rising edge of FSCCLK for the data bit D1 (FSCCLK N-1), but it can go low at the rising edge of FSCCLK for data bit D0 (FSCCLK N) if an unsolicited message has
6.1.3 FINTREQ Behavior: A Special Case
When communicating with DSPAB there are two types of messages which force FINTREQ to go low. These messages are known as solicited messages and unsolicited messages. For more information on the specific types of messages that require a read from the host, one of the application code user's guides should be referenced. In general, when communicating with DSPAB, FINTREQ will not go low unless the host first sends a read request command message. In other words the host must solicit a response from the DSP. In this environment, the host must read from DSPAB until FINTREQ goes high again. Once the FINTREQ pin has gone high it will not be driven low until the host sends another read request. When unsolicited messages, such as those used for Autodetect, have been enabled, the behavior of FINTREQ is noticeably different. DSPAB will drop the FINTREQ pin whenever it has an outgoing message, even though the host may not have requested data. There are three ways in which FINTREQ can be affected by an unsolicited message: 1) During normal operation, while FINTREQ is high, DSPAB could drop FINTREQ to indicate an outgoing message, without a prior read request. 2) The host is in the process of reading from DSPAB, meaning that FINTREQ is already low. An unsolicited message arrives which forces FINTREQ to remain low after the solicited message is read. 3) The host is reading from DSPAB when the unsolicited message is queued, but FINTREQ goes
48
arrived. If no unsolicited messages arrive, the FINTREQ pin will remain high after rising. Ideally, the host will sample FINTREQ on the falling edge of FSCCLK number N-1 of the final byte of each read response message. If FINTREQ is sampled high, the host should conclude the current read cycle using the stop condition defined for the communication mode chosen. The host should then begin a new read cycle complete with the appropriate start condition and the chip address. If FINTREQ is sampled low, the host should continue reading the next message from DSPAB without ending the current read cycle. When using automated communication ports, however, the host is often limited to sampling the status of FINTREQ after an entire byte has been transferred. In this situation a low-high-low transition (case 3) would be missed and the host will see a constantly low FINTREQ pin. Since the host should read from DSPAB until it detects that FINTREQ has gone high, this condition will be treated as a multiple-message read (more than one read response is provided by DSPAB). Under these conditions a single byte of 0x00 will be read out before the unsolicited message. The length of every read response is defined in the user's manual for each piece of application code. Thus, the host should know how many bytes to expect based on the first byte (the OPCODE) of a read response message. It is guaranteed that no read responses will begin with 0x00, which means that a
NULL byte (0x00) detected in the OPCODE position of a read response message should be discarded. Please see an Application Code User's Guide for an explanation of the OPCODE. It is important that the host be aware of the presence of NULL bytes, or the communication channel could become corrupted. When case (3) occurs and the host issues a stop condition before starting a new read cycle, the first byte of the unsolicited message is loaded directly into the shift register and 0x00 is never seen. Alternatively, if case (3) occurs and the host continues to read from DSPAB without a stop condition (a multiple message read), the 0x00 byte must be shifted out of DSPAB before the first byte of the unsolicited message can be read. In other words, if a host can only sample FINTREQ after an entire byte transfer the following routine should be used if FINTREQ is low after the last byte of the message being read: 1) Read one byte 2) If the byte = 0x00 discard it and skip to step 3. If the byte != 0x00 then it is the OPCODE for the next message. For this case skip to step 4. 3) Read one more byte. This is the OPCODE for the next message. 4) Read the rest of the message as indicated in the previous sections.
49
6.2 Parallel Host Communication for DSPAB
The parallel host communication modes of DSPAB provide an 8-bit interface to the DSP. An Intel-style parallel mode and a Motorola-style parallel mode are supported. The host interface is implemented using four communication registers within DSPAB as shown in Table 6, "Parallel Input/Output Registers for DSPAB," on page 51. When the host is downloading code to DSPAB or configuring the application code, control messages will be written to (and read from) the Host Message register. The Host Control register is used during messaging sessions to determine when DSPAB can accept another byte of control data, and when DSPAB has an outgoing byte that should be read. All communication to DSPAB after download is in 24-bit words. Reads and writes are done in multiples of 3-byte transactions. A 3-byte transaction is accomplished by doing three consecutive byte reads or byte writes. The PCM Data and Compressed Data registers are used strictly for the transfer of audio data. The host cannot read from these two registers. Audio data written to registers 11b and 10b are transferred directly to the internal FIFOs of DSPAB. When the level of the PCM FIFO reaches the FIFO threshold level, the MFC bit of the Host Control register will be set. When the level of the Compressed Data FIFO reaches the FIFO threshold level, the MFB bit of the Host Control register will be set. Writing data directly to the FIFOs is only supported in specific applications. To see if an application supports this feature, consult the appropriate Application Note. A detailed description for each parallel host mode will now be given. The following information will be provided for the Intel mode and Motorola mode: * * The pins of DSPAB which must be used for proper communication Flow diagram and description for a parallel byte write
*
Flow diagram and description for a parallel byte read
The four registers of DSPAB's parallel host mode are not used identically. The algorithm used for communicating with each register will be given as a functional description, building upon the basic read and write protocols defined in the Motorola and Intel sections. The following will be covered: * * Flow diagram and description for a control write Flow diagram and description for a control read
6.2.5 Intel Parallel Host Communication Mode for DSPAB
The Intel parallel host communication mode is implemented using the pins given in Table 6. Parallel host communication is available only on the 144-pin package part.
Mnemonic Pin Name 144-Pin Package, Pin Number 15 12 13 4 6 16 9 14 18 19 22 24 27 29
Chip Select Write Enable Output Enable Register Address Bit 1 Register Address Bit 0 Interrupt Request DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0
FCS FWR FRD FA1 FA0 FINTREQ FDAT7 FDAT6 FDAT5 FDAT4 FDAT3 FDAT2 FDAT1 FDAT0
Table 6. Intel Mode Communication Signals for DSPAB
The HOUTRDY bit of the Host Control Register (A[1:0] = 01b) indicates that the DSP has a message for the host to read. The FINTREQ pin can be controlled by the application code, and allows for another method of requesting that the
50
6.2.1 Host Message (HOSTMSG) Register, A[1:0] = 00b
7 HOSTMSG7 6 HOSTMSG6 5 HOSTMSG5 4 HOSTMSG4 3 HOSTMSG3 2 HOSTMSG2 1 HOSTMSG1 0 HOSTMSG0
HOSTMSG7-0
Host data to and from the DSP. A read or write of this register operates handshake bits between the internal DSP and the external host. This register typically passes multibyte messages carrying microcode, control, and configuration data (messages are written MSB first). HOSTMSG is physically implemented as two independent registers for input and output (Read and write).
6.2.2 Host Control (CONTROL) Register, A[1:0] = 01b
7 Reserved 6 CMPRST 5 PCMRST 4 MFC 3 MFB 2 HINBSY 1 HOUTRDY 0 Reserved
Reserved CMPRST
Always write a 0 for future compatibility. When set, initializes the CMPDATA compressed data input channel. Writing a one to this bit holds the port in reset. Writing zero enables the port. This bit must be low for normal operation. (Write only) When set, initializes the PCMDATA linear PCM input channel. Writing a one to this bit holds the port in reset. Writing zero enables the port. This bit must be low for normal operation. (Write only) When high, indicates that the PCMDATA input buffer is almost full. (Read only) When high, indicates that the CMPDATA input buffer is almost full. (Read only) Set when the host writes to HOSTMSG. Cleared when the DSP reads data from the HOSTMSG register. The host reads this bit to determine if the last host byte written has been read by the DSP. (Read only) Set when the DSP writes to the HOSTMSG register. Cleared when the host reads data from the HOSTMSG register. The DSP reads this bit to determine if the last DSP output byte has been read by the host. (Read only) Always write a 0 for future compatibility.
PCMRST
MFC MFB HINBSY
HOUTRDY
Reserved
6.2.3 PCM Data Input (PCMDATA) Register, A[1:0] = 10b
7 PCMDATA7 6 PCMDATA6 5 PCMDATA5 4 PCMDATA4 3 PCMDATA3 2 PCMDATA2 1 PCMDATA1 0 PCMDATA0
PCMDATA7-0
The host writes PCM data to the DSP input buffer at this address. (Write only)
6.2.4 Compressed Data Input (CMPDATA) Register, A[1:0] = 11b
7 CMPDATA7 6 CMPDATA6 5 CMPDATA5 4 CMPDATA4 3 CMPDATA3 2 CMPDATA2 1 CMPDATA1 0 CMPDATA0
Table 6. Parallel Input/Output Registers for DSPAB
51
ADDRESS A PARALLEL I/O REGISTER (FA[1:0] SET APPROPRIATELY)
1) The host must first drive the FA1 and FA0 register address pins of DSPAB with the address of the desired Parallel I/O Register. The address must be maintained for the duration of the write cycle. Host Message: FA[1:0]==00b. Host Control: PCMDATA: FA[1:0]==01b. FA[1:0]==10b. FA[1:0]==11b.
FCS (LOW) FWR (LOW)
WRITE BYTE TO FDAT[7:0]
CMPDATA:
FCS (HIGH) FWR (HIGH)
2) The host then indicates that the selected register will be written. The host initiates a write cycle by driving the FCS and FWR pins low. 3) The host drives the data byte to the FDAT[7:0] pins of DSPAB. 4) Once the setup time for the write has been met, the host ends the write cycle by driving the FCS and FWR pins high.
Figure 36. Intel Mode, One-Byte Write Flow Diagram for DSPAB
host read a message. When the code supports FINTREQ notification, the FINTREQ pin is asserted (driven low) when the DSP has an outgoing message for the host. FINTREQ is useful for informing the host of unsolicited messages without polling. An unsolicited message is defined as a message generated by the DSP without an associated host read request. Unsolicited messages are used to notify the host of conditions such as a change in the incoming audio data type (e.g. PCM --> AC-3). Most unsolicited messages must be specifically enabled by setting the appropriate bit in the application's manager, enabling autodetection, or enabling other host notification capabilities.
6.2.5.2 Reading a Byte in Intel Mode for DSPAB
Information provided in this section is intended as a functional description of how to read control information from DSPAB. The system designer must ensure that all of the timing constraints of the Intel Parallel Host Mode Read Cycle are met. The flow diagram shown in Figure 37 illustrates the sequence of events that define a one-byte read in Intel mode. The protocol presented in Figure 37 will now be described in detail. 1) The host must first drive the FA1 and FA0 register address pins of DSPAB with the address of the desired Parallel I/O Register. Note that only the Host Message register and the Host Control register can be read. The address must be maintained for the duration of the read cycle. Host Message: FA[1:0]==00b. Host Control: FA[1:0]==01b. 2) The host initiates a read cycle by driving the FCS and FRD pins low (bus must be tri-stated
6.2.5.1 Writing a Byte in Intel Mode for DSPAB
Information provided in this section is intended as a functional description of how to write control information to DSPAB. The system designer must ensure that all of the timing constraints of the Intel Parallel Host Mode Write Cycle are met. The flow diagram shown in Figure 36 illustrates the sequence of events that define a one-byte write in Intel mode. The protocol presented in Figure 36 will now be described in detail.
52
ADDRESS A PARALLEL I/O REGISTER (FA[1:0] SET APPROPRIATELY)
Mnemonic
Pin Name
FCS (LOW) FRD (LOW)
READ BYTE FROM FDAT[7:0]
FCS (HIGH) FRD (HIGH)
Figure 37. Intel Mode, One-Byte Read Flow Diagram for DSPAB
Chip Select Data Strobe Read or Write Select Register Address Bit 1 Register Address Bit 0 Interrupt Request DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0
FCS FDS FR/W FA1 FA0 FINTREQ FDAT7 FDAT6 FDAT5 FDAT4 FDAT3 FDAT2 FDAT1 FDAT0
144-Pin Package, Pin Number 15 12 13 4 6 16 9 14 18 19 22 24 27 29
before this occurs). 3) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the value of the selected register from the FDAT[7:0] pins of DSPAB. 4) The host should now terminate the read cycle by driving the FCS and FRD pins high.
Table 7. Motorola Mode Communication Signals for DSPAB
6.2.6 Motorola Parallel Communication Mode for DSPAB
The Motorola parallel host communication mode is implemented using the pins given in Table 7. Parallel host communication is available only on the 144-pin package part . The HOUTRDY bit of the Host Control Register (A[1:0] = 01b) indicates that the DSP has a message for the host to read. The FINTREQ pin can be controlled by the application code, and allows for another method of requesting that the host read a message. When the code supports FINTREQ notification, the FINTREQ pin is asserted (driven low) whenever the DSP has an outgoing message for the host.
FINTREQ is useful for informing the host of unsolicited messages. An unsolicited message is defined as a message generated by the DSP without an associated host read request. Unsolicited messages are used to notify the host of conditions such as a change in the incoming audio data type (e.g. PCM --> AC-3). Most unsolicited messages must be specifically enabled by setting the appropriate bit in the application's manager, enabling autodetection, or enabling other host notification capabilities.
6.2.6.1 Writing a Byte in Motorola Mode
Information provided in this section is intended as a functional description of how to write control information to DSPAB. The system designer must ensure that all of the timing constraints of the Motorola Parallel Host Mode Write Cycle are met. The flow diagram shown in Figure 38 illustrates the sequence of events that define a one-byte write in Motorola mode. The protocol presented in Figure 38 will now be described in detail. 1) The host must drive the FA1 and FA0 register address pins of DSPAB with the address of the
53
address of the desired Parallel I/O Register. The address must be maintained for the duration of the read cycle. Host Message: FA[1:0]==00b. Host Control: PCMDATA: CMPDATA: FA[1:0]==01b. FA[1:0]==10b. FA[1:0]==11b.
protocol presented in Figure 39 will now be described in detail. 1) The host must drive the FA1 and FA0 register address pins of DSPAB with the address of the desired Parallel I/O Register. Note that only the Host Message register and the Host Control register can be read. The address must be maintained for the duration of the read cycle. Host Message: Host Control: FA[1:0]==00b. FA[1:0]==01b.
2) The host indicates that this is a write cycle by driving the FR/W pin low. 3) The host initiates a write cycle by driving the FCS and FDS pins low. 4) The host drives the data byte to the FDAT[7:0] pins of DSPAB. 5) Once the setup time for the write has been met, the host ends the write cycle by driving the FCS and FDS pins high.
2) The host indicates that this is a read cycle by driving the FR/W pin high. 3) The host initiates the read cycle by driving the FCS and FDS pins low (bus must be tri-stated by this time). 4) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the value of the selected register from the FDAT[7:0] pins of DSPAB. 5) The host should now terminate the read cycle by driving the FCS and FDS pins high.
FR/W (HIGH) ADDRESS A PARALLEL I/O REGISTER (FA[1:0] SET APPROPRIATELY)
6.2.6.2 Reading a Byte in Motorola Mode
The flow diagram shown in Figure 39, "Motorola Mode, One-Byte Read Flow Diagram for DSPAB" on page 54 illustrates the sequence of events that define a one-byte read in Motorola mode. The
FR/W (LOW) ADDRESS A PARALLEL I/O REGISTER (FA[1:0] SET APPROPRIATELY)
FCS (LOW) FDS (LOW)
FCS (LOW) FDS (LOW)
WRITE BYTE TO FDAT[7:0]
READ BYTE FROM FDAT[7:0]
FCS (HIGH) FDS (HIGH)
FCS (HIGH) FDS (HIGH)
Figure 38. Motorola Mode, One-Byte Write Flow Diagram for DSPAB
Figure 39. Motorola Mode, One-Byte Read Flow Diagram for DSPAB
54
6.2.7 Procedures for Parallel Host Mode Communication for DSPAB 6.2.7.1 Control Write in a Parallel Host Mode for DSPAB
When writing control data to DSPAB, the same protocol is used whether the host is writing a control message or an entire executable download image. Messages sent to DSPAB should be written most significant byte first. Likewise, downloads of the application code should also be performed most significant byte first. The example shown in this section can be generalized to fit any control write situation. The generic function `Read_Byte_*()' is used in the following example as a generalized reference to either Read_Byte_MOT() (read a byte in Motorola mode) or Read_Byte_INT() (read a byte in Intel mode), and `Write_Byte_*()' is a generic reference to Write_Byte_MOT() (write a byte in Motorola mode) or Write_Byte_INT() (write a byte in Intel mode). Figure 40 shows a typical write sequence. The protocol presented in Figure 40 will now be described in detail. 1) When the host is communicating with DSPAB, the host must verify that DSPAB is ready to accept a new control byte. If DSPAB has not read the previous byte from the control port, it will be unable to receive another byte. 2) In order to determine whether DSPAB is ready to accept a new control byte the host must read the HINBSY bit of the Host Control Register (bit 2 in FA[1:0]=01b) using the selected communication mode (Intel or Motorola). If HINBSY is high, then the DSP is not prepared to accept a new control byte, and the host should poll the Host Control Register again. If HINBSY is low, then the host may write a control byte into the Host Message Register. 3) Once the host knows that the DSP is ready for a new control byte, it should write the control byte to the Host Message Register (FA[1:0] =
00b) using the selected communication mode (Intel or Motorola). 4) If the host would like to write any more control bytes to DSPAB, the host should once again poll the Host Control Register (return to step 1).
6.2.7.2 Control Read in a Parallel Host Mode for DSPAB
When reading control data from DSPAB, the same protocol is used whether the host is reading a single byte, a 6 byte message, or a string of messages. During the boot procedure, a handshaking protocol is used by DSPAB. This handshake consists of a 3 byte write to DSPAB followed by a 1 byte response from the DSP. The host must read the response byte and act accordingly. The boot procedure is discussed in Section 8 "Boot Procedure" on page 71. During regular operation (at run-time), the responses from DSPAB will always be 6 bytes in length.
READ_BYTE_*(HOST CONTROL REGISTER)
Y HINBSY == 1 N WRITE_BYTE_*(HOST MESSAGE REGISTER)
Y
MORE BYTES TO WRITE? N FINISHED
Figure 40. Typical Parallel Host Mode Control Write Sequence Flow Diagram for DSPAB 55
The example shown in this section can be used for any control read situation. The generic function `Read_Byte_*()' is used in the following example as a generalized reference to either Read_Byte_MOT() (Motorola byte read) or Read_Byte_INT() (Intel byte read). Figure 41 shows a typical read sequence. The protocol presented in Figure 41 will now be described in detail.
F IN T R E Q = 0 ? ( o p tio n a l) Y R E A D _ B Y T E _ *( H O S T C O N T R O L R E G IS T E R )
DSPAB has an outgoing message. Note that even with the use of FINTREQ, HOUTRDY must be checked to ensure that the current byte is ready to be read by the host during the read process. Please note that the state of FINTREQ is undefined during boot, and it is valid only once the application code is loaded. 2) The host reads the Host Control Register (FA[1:0] = 01b) in order to determine the state of the communication interface. 3) In order to determine whether DSPAB has an outgoing control byte that is valid, the host must check the HOUTRDY bit of the Host Control Register (bit 1, FA[1:0] = 01b). If HOUTRDY is high, then the Host Message Register contains a valid message byte for the host. If HOUTRDY is low, then the DSP has not placed a new control byte in the Host Message Register, and the host should poll the Host Control Register again. 4) Once the host knows that the DSP is ready to provide a new response byte, the host can safely read a byte from the Host Message Register (FA[1:0] = 00b) using the appropriate communication protocol (Motorola or Intel). 5) If the host expects to read any more response bytes, the host should once again check the HOUTRDY bit (return to step 1). Messages from the application code (post-download) on the DSP will always be 6 bytes, unless otherwise stated in the associated Application Note. 6) After the response has been read the host should wait at least 100 uS and check HOUTRDY one final time. If HOUTRDY is high once again this means that an unsolicited message has come during the read process and the host has another message to read (i.e. skip back to step 4 and read out the new message). It is the host's responsibility to insure that any pending messages are read from the DSP.
N H OUTR DY == 1 Y R E A D _ B Y T E _ *( H O S T M E S S A G E R E G IS T E R )
Y
MORE BYTES TO READ?
N W A IT 1 0 0 M IC R O S E C
R E A D _ B Y T E _ *( H O S T C O N T R O L R E G IS T E R )
Y H OUTR DY == 1
N F IN IS H E D
Figure 41. Typical Parallel Host Mode Control Read Sequence Flow Diagram for DSPAB
1) Optionally, FINTREQ going low may be used as an interrupt to the host to indicate that
56
Failure to do this may cause the DSP's output message buffer to overflow, corrupting any pending outbound messages.
6.3 Parallel Host Communication for DSPC
The parallel host communication modes of DSPC provide an 8-bit interface to the DSP. An Intel-style parallel mode and a Motorola-style parallel mode are supported. The host interface is implemented using four communication registers within DSPC as shown in Table 8, "Parallel Input/Output Registers for DSPC," on page 58. The HOSTMSG register is a 32 bit register. Since there are only eight data pins, only one byte can be transferred at a time, but a full 32 bits are transferred in each read or write to this register. When the host is downloading code or configuring the application code in DSPC, control messages must be written to (and read from) the Host Message register 32 bits at a time. The HINBSY pin and the HINBSY bit in the Host Control register are used during messaging sessions to determine when DSPC can accept another 32-bit word of control data. The HINBSY pin and the HINBSY bit (in the Host Control register) go high when the host writes 32 bits (4 bytes) to the HOSTMSG register. The HINBSY pin and HINBSY bit go low when DSPC reads the 32 bit data from the register. The INTREQ pin goes low and the HOUTRDY bit (in the Host Control register) goes high when DSPC has an message that must be read by the host.
The HOSTDATA1 and HOSTDATA2 registers are used strictly for the transfer of audio data to DSPC. The host cannot read from these two registers. Support of these registers is DSPC application code specific, see the appropriate Application Note for availability. A detailed description for each parallel host mode will now be given. The following information will be provided for the Intel mode and Motorola mode: * The pins of DSPC which must be used for proper communication * * * * Flow diagram and description for a parallel byte write Flow diagram and description for a 32-bit word (4-byte) write Flow diagram and description for a parallel byte read Flow diagram and description for a 32-bit word (4-byte) read
The four registers of DSPC's parallel host mode are not used identically. The algorithm used for communicating with each register will be given as a functional description, building upon the basic read and write protocols defined in the Motorola and Intel sections. The following will be covered: * Flow diagram and description for a control write * Flow diagram and description for a control read
57
6.3.1 Host Message (HOSTMSG) Register, A[1:0] = 00b
31 23 15 7 30 22 14 6 29 21 13 5 28 MS_BYTE 20 BYTE_B 12 BYTE_A 4 LS_BYTE 3 2 1 0 11 10 9 8 19 18 17 16 27 26 25 24
The HOSTMSG register is a 32-bit register that is used to read from or write to DSPC. It is read and written in 4-byte transactions. This register passes
MS_BYTE BYTE_B BYTE_A LS_BYTE
all the code, control and configuration data to and from DSPC. Messages are read and written MS_BYTE first.
This is the most significant byte (bits 31:24). This is BYTE_B (bits 23:16). This is BYTE_A (bits 15:8). This is the least significant byte (bits 7:0).
6.3.2 Host Control (CONTROL) Register, A[1:0] = 01b
7 Reserved 6 Reserved 5 Reserved 4 BYTE_SEL 3 2 HINBSY 1 HOUTRDY 0 Reserved
Reserved BYTE_SEL HINBSY
Always write a 0. Always write a 11b to these bits. This bit is the Host Input Ready signal. It is set when the host writes to the HOSTMSG register. It is cleared when DSPC reads the HOSTMSG register. This bit is also pinned out on the HINBSY pin. Read only by the host and DSPC. This bit is set when DSPC writes data to the HOST_MSG register, and indicates that the DSP has a pending message for the host. The HOUTRDY bit is cleared when the host reads the HOSTMSG register. The bit is inverted and pinned out on the INTREQ pin. Read only by the host and DSPC
HOUTRDY
6.3.3 Host Data1 Input (HOSTDATA1) Register, A[1:0] = 10b
7 6 5 4 3 2 1 0 HOSTDATA1_ HOSTDATA1_ HOSTDATA1_ HOSTDATA1_ HOSTDATA1_ HOSTDATA1_ HOSTDATA1_ HOSTDATA1_ 7 6 5 4 3 2 1 0
HOSTDATA1_7-0 The host writes data to DSPC at this address. (Write only)
6.3.4 Host Data2 Input (HOSTDATA2) Register, A[1:0] = 11b
7 6 5 4 3 2 1 0 HOSTDATA2_ HOSTDATA2_ HOSTDATA2_ HOSTDATA2_ HOSTDATA2_ HOSTDATA2_ HOSTDATA2_ HOSTDATA2_ 7 6 5 4 3 2 1 0
HOSTDATA2_7-0 The host writes data to DSPC at this address. (Write only) Table 8. Parallel Input/Output Registers for DSPC
58
6.3.5 Intel Parallel Host Communication Mode for DSPC
The Intel parallel host communication mode is implemented using the pins given in Table 9. Parallel host communication is available only on the 144-pin package version of the CS49400. The INTREQ pin is asserted (driven low) whenever the DSP has an outgoing message for the host. This same information is reflected by the HOUTRDY bit of the Host Control Register (A[1:0] = 01b). INTREQ is useful for informing the host of unsolicited messages. An unsolicited message is defined as a message generated by the DSP without an associated host read request.
Mnemonic Pin Name 144-Pin Package, Pin Number 129 120 121 139 130 3 141 95 96 97 103 105 112 115 116
ADDRESS A PARALLEL I/O REGISTER (A[1:0] SET APPROPRIATELY)
CS (LOW ) W R (LOW )
W RITE BYTE TO HDAT[7:0]
CS (HIGH) W R (HIGH)
Figure 42. Intel Mode, One-Byte Write Flow Diagram for DSPC
Chip Select Write Enable Output Enable Register Address Bit 1 Register Address Bit 0 Interrupt Request Host Busy DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0
CS WR RD A1 A0 INTREQ HINBSY HDAT7 HDAT6 HDAT5 HDAT4 HDAT3 HDAT2 HDAT1 HDAT0
The flow diagram shown in Figure 42 illustrates the sequence of events that define a one-byte write in Intel mode. One-byte writes should only be perfomed to the Host Control and Host Data registers. The protocol presented in Figure 42 will now be described in detail. 1) The host must first drive the A1 and A0 register address pins of DSPC with the address of the desired Parallel I/O Register. The address is latched on the falling edge of CS. Host Control: Host Data1: Host Data2: A[1:0]==01b. A[1:0]==10b. A[1:0]==11b.
Table 9. Intel Mode Communication Signals for DSPC
2) The host initiates a write cycle by driving the CS and WR pins low. 3) The host drives the data byte to the HDAT[7:0] pins of DSPC. 4) Once the setup time for the write has been met, the host ends the write cycle by driving the WR and CS pins high.
6.3.5.1 Writing a Byte in Intel Mode for DSPC
Information provided in this section is intended as a functional description of how to write control information to DSPC. The system designer must ensure that all of the timing constraints of the Intel Parallel Host Mode Write Cycle are met.
59
6.3.5.2 Writing a 32-bit (4-byte) Word in Intel Mode for DSPC
Information provided in this section is intended as a functional description of how to write control information to DSPC. The system designer must ensure that all of the timing constraints of the Intel Parallel Host Mode Write Cycle are met. The flow diagram shown in Figure 43 illustrates the sequence of events that define a 4-byte write in Intel mode. 32-bit (4-byte) writes should only be used to write to the Host Message register. The protocol presented in Figure 43 will now be described in detail. 1) The host must first drive the A1 and A0 register address pins of DSPC with the address of the desired Parallel I/O Register (both low for A1=A0=0). The address must be maintained for the duration of the write cycle, and is latched on the falling edge of CS and WR. Host Message: A[1:0]==00b. 2) The host initiates a write cycle by driving the CS and WR pins low. 3) The host drives the most significant data byte (bits 31:24) to the HDAT[7:0] pins of DSPC. 4) Once the setup time for the write has been met, the host drives WR high to strobe in the most significant data byte. 5) The host drives WR low. 6) The host drives the next most significant data byte, BYTE_B (bits 23:16), to the HDAT[7:0] pins of DSPC. 7) Once the setup time for the write has been met, the host drives WR high to strobe in the data byte. 8) The host drives WR low. 9) The host drives the next most significant data byte, BYTE_A (bits 15:8), to the HDAT[7:0] pins of DSPC.
ADDRESS A PARALLEL I/O REGISTER (A[1:0] SET APPROPRIATELY)
CS (LOW) RD (LOW)
READ BYTE FROM HDAT[7:0]
CS (HIGH) RD (HIGH)
Figure 44. Intel Mode, One-Byte Read Flow Diagram for DSPC
10) Once the setup time for the write has been met, the host drives WR high to strobe in the data byte. 11) The host drives WR low. 12) The host drives the least significant data byte (bits 7:0) to the HDAT[7:0] pins of DSPC. 13) Once the setup time for the write has been met, the host drives WR high to strobe in the data byte. 14) The host drives CS high to end the write transaction.
6.3.5.3 Reading a Byte in Intel Mode for DSPC
Information provided in this section is intended as a functional description of how to read control information from DSPC. The system designer must ensure that all of the timing constraints of the Intel Parallel Host Mode Read Cycle are met. The flow diagram shown in Figure 44 illustrates the sequence of events that define a one-byte read in Intel mode. One-byte reads should only be done with the Host Control register. The protocol presented in Figure 44 will now be described in detail.
60
ADDRESSAPARALLELI/OREG ISTER (A[1:0] SETAPPROPRIATELY)
CS(LOW) WR(LOW)
WRITEM S_BYTETO HDAT[7:0]
1) The host must first drive the A1 and A0 register address pins of DSPC with the address of the desired Parallel I/O Register (A1=0, A0=1). Note that only the Host Control register can be read using a byte read. The address must be maintained for the duration of the read cycle, and is latched on the falling edge of CS. Host Control: A[1:0]==01b. 2) The host initiates a read cycle by driving the CS and RD pins low (bus must be tri-stated by this time). 3) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the value of the selected register from the HDAT[7:0] pins of DSPC. 4) The host should now terminate the read cycle by driving the CS and RD pins high.
WR(HIG H)
WR(LOW)
WRITEBYTE_BTO HDAT[7:0]
WR(HIG H)
WR(LOW)
6.3.5.4 Reading a 32-bit (4-byte) Word from DSPC in Intel Mode
Information provided in this section is intended as a functional description of how to read control information from DSPC. The system designer must ensure that all of the timing constraints of the Intel Parallel Host Mode Read Cycle are met. The flow diagram shown in Figure 45, "Intel Mode, 32-Bit (4-Byte) Read Flow Diagram for DSPC" on page 62 illustrates the sequence of events that define a 4-byte read in Intel mode. 4byte (32-bit) reads should only be done with the Host Message register. The protocol presented in Figure 45 will now be described in detail. 1) The host must first drive the A1 and A0 register address pins of DSPC with the address of the desired Parallel I/O Register (A1=A0=0). Note that only the Host Message register can be read using a 4-byte read cycle. The address must be maintained for the duration of the read cycle, and is latched on the falling edge of CS. Host Message: A[1:0]==00b.
61
WRITEBYTE_ATO HDAT[7:0]
WR(HIG H)
WR(LOW)
WRITELS_BYTETO HDAT[7:0]
WR(HIG H)
CS(HIG H)
Figure 43. Intel Mode, 32-bit (4-byte) Write Flow Diagram for DSPC
ADDRESS A PARALLEL I/O REGISTER (A[1:0] SET APPROPRIATELY)
2) The host initiates a read cycle by driving the CS and RD pins low (bus must be tri-stated by this time). 3) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the most significant data byte (bits 31:24) from the HDAT[7:0] pins of DSPC. 4) The host drives RD high to indicate that the data byte has been read. 5) The host drives RD low to clock out the next data byte. 6) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read BYTE_B (bits 23:16) from the HDAT[7:0] pins of DSPC. 7) The host drives RD high to indicate that the data byte has been read. 8) The host drives RD low to clock out the next data byte. 9) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read BYTE_A (bits 15:8) from the HDAT[7:0] pins of DSPC. 10) The host drives RD high to indicate that the data byte has been read.
CS (LOW) RD (LOW)
READ MS_BYTE FROM HDAT[7:0]
RD (HIGH)
RD (LOW)
READ BYTE_B FROM HDAT[7:0]
RD (HIGH)
RD (LOW)
READ BYTE_A FROM HDAT[7:0]
RD (HIGH)
RD (LOW)
11) The host drives RD low to clock out the next data byte. 12) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the least significant data byte (bits 7:0) from the HDAT[7:0] pins of DSPC. 13) The host drives RD high to indicate that the data byte has been read. 14) The host should now terminate the read cycle by driving the CS pin high.
READ LS_BYTE FROM HDAT[7:0]
RD (HIGH)
CS (HIGH)
Figure 45. Intel Mode, 32-Bit (4-Byte) Read Flow Diagram for DSPC
62
6.3.6 Motorola Parallel Host Communication Mode for DSPC
The Motorola parallel host communication mode is implemented using the pins given in Table 10.
Mnemonic Pin Name 144-Pin Package, Pin Number 129 120 121 139 130 3 141 95 96 96 103 105 112 115 116
R/W (LOW ) ADDRESS A PARALLEL I/O REGISTER (A[1:0] SET APPROPRIATELY)
CS (LOW ) DS (LOW )
Chip Select Data Strobe Read or Write Select Register Address Bit 1 Register Address Bit 0 Interrupt Request Host Busy DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0
CS DS R/W A1 A0 INTREQ HINBSY HDAT7 HDAT6 HDAT5 HDAT4 HDAT3 HDAT2 HDAT1 HDAT0
W RITE BYTE TO HDAT[7:0]
CS (HIGH) DS (HIGH)
Figure 46. Motorola Mode, One-Byte Write Flow Diagram for DSPC
6.3.6.1 Writing a Byte in Motorola Mode for DSPC
Information provided in this section is intended as a functional description of how to write control information to DSPC. The system designer must ensure that all of the timing constraints of the Motorola Parallel Host Mode Write Cycle are met. The flow diagram shown in Figure 46 illustrates the sequence of events that define a one-byte write in Motorola mode. One byte writes should only be used with the Host Control and Host Data registers. The protocol presented in Figure 46 will now be described in detail. 1) The host must first drive the A1 and A0 register address pins of DSPC with the address of the desired Parallel I/O Register. The address is latched on the falling edge of CS. Host Control: Host Data1: Host Data2: A[1:0]==01b. A[1:0]==10b. A[1:0]==11b.
Table 10. Motorola Mode Communication Signals for DSPC
Parallel host communication is available only on the 144-pin package part. The INTREQ pin is asserted (driven low) whenever the DSP has an outgoing message for the host. This same information is reflected by the HOUTRDY bit of the Host Control Register (A[1:0] = 01b). INTREQ is useful for informing the host of unsolicited messages. An unsolicited message is defined as a message generated by DSPC without an associated host read request.
2) The host indicates that this is a write cycle by driving the R/W pin low.
63
3) The host initiates a write cycle by driving the CS and DS pins low. 4) The host drives the data byte to the HDAT[7:0] pins of DSPC. 5) Once the setup time for the write has been met, the host ends the write cycle by driving the DS and CS pins high.
R/W (LOW) ADDRESS A PARALLEL I/O REGISTER (A[1:0] SET APPROPRIATELY)
CS (LOW) DS (LOW)
WRITE MS_BYTE TO HDAT[7:0]
6.3.6.2 Writing a 32-bit (4-byte) Word in Motorola Mode for DSPC
Information provided in this section is intended as a functional description of how to write control information to DSPC. The system designer must ensure that all of the timing constraints of the Motorola Parallel Host Mode Write Cycle are met. The flow diagram shown in Figure 43 illustrates the sequence of events that define a 32-bit (4-byte) write in Motorola mode. 32-bit (4-byte) writes should only be done to the Host Message register. The protocol presented in Figure 43 will now be described in detail. 1) The host must first drive the A1 and A0 register address pins of DSPC with the address of the desired parallel I/O register (A1=A0=0). The address must be maintained for the duration of the write cycle, and is latched on the falling edge of CS. Host Message: A[1:0]==00b. 2) The host indicates that this is a write cycle by driving the R/W pin low. 3) The host initiates a write cycle by driving the CS and DS pins low. 4) The host drives the most significant data byte (bits 31:24) to the HDAT[7:0] pins of DSPC. 5) Once the setup time for the data has been met, the host latches this byte in by driving DS high. 6) The host drive DS low. 7) The host drives the next most significant data byte, BYTE_B (bits 23:16), to the HDAT[7:0]
DS (HIGH)
DS (LOW)
WRITE BYTE_B TO HDAT[7:0]
DS (HIGH)
DS (LOW)
WRITE BYTE_A TO HDAT[7:0]
DS (HIGH)
DS (LOW)
WRITE LS_BYTE TO HDAT[7:0]
DS (HIGH)
CS (HIGH)
Figure 47. Motorola Mode, 32-bit (4-byte) Write Flow Diagram for DSPC
64
pins of DSPC. 8) Once the setup time for the data has been met, the host latches this byte in by driving DS high. 9) The host drive DS low. 10) The host drives the next most significant data byte, BYTE_A (bits 15:8), to the HDAT[7:0] pins of DSPC. 11) Once the setup time for the data has been met, the host latches this byte in by driving DS high. 12) The host drive DS low. 13) The host drives the least significant data byte (bits 7:0) to the HDAT[7:0] pins of DSPC. 14) Once the setup time for the data has been met, the host latches this byte in by driving DS high. 15) The host ends the write cycle by driving the CS pin high.
CS (HIGH) DS (HIGH) CS (LOW ) DS (LOW ) R/W (HIGH) A DDRE SS A PA RALLE L I/O REGISTE R (A [1:0] S ET AP PRO PRIA TE LY)
RE AD B YT E F ROM HDA T[7:0]
Figure 48. Motorola Mode, One-Byte Read Flow Diagram for DSPC
6.3.6.3 Reading a Byte in Motorola Mode for DSPC
Information provided in this section is intended as a functional description of how to write control information to DSPC. The system designer must ensure that all of the timing constraints of the Motorola Parallel Host Mode Read Cycle are met. The flow diagram shown in Figure 48 illustrates the sequence of events that define a one-byte read in Motorola mode. Single byte reads should only be done with the Host Control register. The protocol presented in Figure 48 will now be described in detail. 1) The host must first drive the A1 and A0 register address pins of DSPC with the address of the desired Parallel I/O Register (A1=0, A0=1). The address must be maintained for the duration of the read cycle, and is latched on the falling edge of CS. Host Control: A[1:0]==01b. 2) The host indicates that this is a read cycle by driving the R/W pin high.
3) The host initiates a read cycle by driving the CS and DS pins low (bus must be tri-stated by this time). 4) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the value of the selected register from the HDAT[7:0] pins of DSPC. 5) The host should now terminate the read cycle by driving the CS and DS pins high.
6.3.6.4 Reading a 32-bit (4-byte) word from DSPC in Motorola mode
Information provided in this section is intended as a functional description of how to read control information from DSPC. The system designer must ensure that all of the timing constraints of the Motorola Parallel Host Mode Read Cycle are met. The flow diagram shown in Figure 49, "Motorola Mode, 32-Bit (4-Byte) Read Flow Diagram for DSPC" on page 66 illustrates the sequence of events that define a 32-bit (4-byte) read in Motorola mode. Reading a 32-bit (4-byte) word should only be done with the Host Message
65
R/W (HIGH) ADDRESS A PARALLEL I/O REGISTER (A[1:0] SET APPROPRIATELY)
register. The protocol presented in Figure 49 will now be described in detail. 1) The host must first drive the A1 and A0 register address pins of DSPC with the address of the desired Parallel I/O Register (A1=A0=0). Note that only the Host Message register can be read using 4-byte reads. The address must be maintained for the duration of the read cycle, and is latched on the falling edge of CS. Host Message: A[1:0]==00b. 2) The host indicates that this is a read cycle by driving the R/W pin high. 3) The host initiates a read cycle by driving the CS and DS pins low (bus must be tri-stated by this time). 4) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the most significant byte (bits 31:24) from the HDAT[7:0] pins of DSPC. 5) The host indicates the byte has been read by driving DS high. 6) The host latches out the next byte by driving DS low.
CS (LOW) DS (LOW)
READ MS_BYTE TO HDAT[7:0]
DS (HIGH)
DS (LOW)
READ BYTE_B TO HDAT[7:0]
DS (HIGH)
DS (LOW)
READ BYTE_A TO HDAT[7:0]
DS (HIGH)
DS (LOW)
READ LS_BYTE TO HDAT[7:0]
7) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the next most significant byte, BYTE_B (bits 23:16), of the selected register from the HDAT[7:0] pins of DSPC. 8) The host indicates the byte has been read by driving DS high. 9) The host latches out the next byte by driving DS low.
DS (HIGH)
CS (HIGH)
Figure 49. Motorola Mode, 32-Bit (4-Byte) Read Flow Diagram for DSPC
10) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the next most significant byte, BYTE_A (bits 15:8), of the selected register from the HDAT[7:0] pins of
66
DSPC. 11) The host indicates the byte has been read by driving DS high. 12) The host latches out the next byte by driving DS low. 13) Once the data is valid (after waiting the appropriate time specified in the timing specifications), the host can read the least significant byte (bits 7:0) of the selected register from the HDAT[7:0] pins of DSPC. 14) The host indicates the byte has been read by driving DS high. 15) The host should now terminate the read cycle by driving the CS pin high.
generic reference to Write_Word_MOT() (write a 32-bit word in Motorola mode) or Write_Word_INT() (write a 32-bit word in Intel mode). Figure 50 shows a typical write sequence. The protocol presented in Figure 50 will now be described in detail. 1) When the host is communicating with DSPC, the host must verify that DSPC is ready to accept a new 32-bit control word. If DSPC has not read the previous word from the control port, it will be unable to receive another word. 2) In order to determine whether DSPC is ready to accept a new 32-bit control word the host must read the HINBSY bit of the Host Control Register (bit 2 in FA[1:0]=01b) using the selected communication mode (Intel or Motorola). If HINBSY is high, then the DSP is not prepared to accept a new control word, and the host should poll the Host Control Register again. If HINBSY is low, then the host may write a control word (32-bits) into the Host
6.3.7 Procedures for Parallel Host Mode Communication for DSPC 6.3.7.1 Control Write in a Parallel Host Mode for DSPC
When writing control data to DSPC, the same protocol is used whether the host is writing a control message or an entire executable download image. Messages sent to DSPC should be written most significant byte first. Likewise, downloads of the application code should also be performed most significant byte first. The example shown in this section can be generalized to fit any control write situation. The generic function `Read_Byte_*()' is used in the following example as a generalized reference to either Read_Byte_MOT() (read a byte in Motorola mode) or Read_Byte_INT() (read a byte in Intel mode), and `Write_Byte_*()' is a generic reference to Write_Byte_MOT() (write a byte in Motorola mode) or Write_Byte_INT() (write a byte in Intel mode). Similarly, the generic function `Read_Word_*()' is used in the following example as a generalized reference to either Read_Word_MOT() (read a 32-bit word in Motorola mode) or Read_Word_INT() (read a 32bit word in Intel mode), and `Write_Word_*()' is a
READ_BYTE_*(HOST CONTROL REGISTER)
Y HINBSY == 1 N WRITE_WORD_*(HOST MESSAGE REGISTER)
Y
MORE BYTES TO WRITE? N FINISHED
Figure 50. Typical Parallel Host Mode Control Write Sequence Flow Diagram for DSPC 67
Message Register. 3) Once the host knows that the DSP is ready for a new control word, it should write the 32-bit control word to the Host Message Register (FA[1:0] = 00b) using the selected communication mode (Intel or Motorola). 4) If the host would like to write any more 32-bit control words to DSPC, the host should once again poll the Host Control Register (return to step 1).
FINTREQ = 0? Y READ_BYTE_*( HOST CONTROL REGISTER)
HOUTRDY == 1 Y READ_WORD_*( HOST MESSAGE REGISTER)
N
6.3.7.2 Control Read in a Parallel Host Mode for DSPC
When reading control data from DSPC, the same protocol is used whether the host is reading a single 32-bit word, or a string of message words. Reads and writes to the Host Message Register are always 32-bits (4-bytes), and reads of the Host Control Register are always a single byte. The example shown in this section can be used for any control read situation. The generic function `Read_Word_*()' is used in the following example as a generalized reference to either Read_Word_MOT() (Motorola 32-bit word read) or Read_Word_INT() (Intel 32-bit word read). Figure 51 shows a typical read sequence. The protocol presented in Figure 51 will now be described in detail. 1) Optionally, INTREQ going low may be used as an interrupt to the host to indicate that DSPC has an outgoing message. 2) The host reads the Host Control Register (A[1:0] = 01b) in order to determine the state of the communication interface. 3) In order to determine whether DSPC has an outgoing control word that is valid, the host must check the HOUTRDY bit of the Host Control Register (bit 1, A[1:0] = 01b). If HOUTRDY is high, then the Host Message Register contains a valid 32-bit word for the host. If HOUTRDY is low, then the DSP has
Y
MORE WORDS TO READ?
N WAIT 100 MICROSEC
READ_BYTE_*( HOST CONTROL REGISTER)
Y HOUTRDY == 1
N FINISHED
Figure 51. Typical Parallel Host Mode Control Read Sequence Flow Diagram for DSPC
not placed a new control word in the Host Message Register, and the host should poll the Host Control Register again. 4) Once the host knows that the DSP is ready to provide a new 32-bit response word, the host can safely read a word from the Host Message Register (A[1:0] = 00b) using the appropriate communication protocol (Motorola or Intel). 5) If the host expects to read more 32-bit response words, the host should once again check the
68
HOUTRDY bit (return to step 1). 6) After the response has been read the host should wait at least 100 uS and check HOUTRDY one final time. If HOUTRDY is high once again this means that an unsolicited message has come during the read process and the host has another message to read (i.e. skip back to step 4 and read out the new message). It is the host's responsibility to insure that any pending messages are read from the DSP. Failure to do this may cause the DSP's output message buffer to overflow, corrupting any pending outbound messages.
Pin Name Pin Description EXTA0 SRAM Address 0 EXTA1 SRAM Address 1 EXTA2 SRAM Address 2 EXTA3 SRAM Address 3 EXTA4 SRAM Address 4 EXTA5 SRAM Address 5 EXTA6 SRAM Address 6 EXTA7 SRAM Address 7 EXTA8 SRAM Address 8 EXTA9 SRAM Address 9 EXTA10 SRAM Address 10 EXTA11 SRAM Address 11 EXTA12 SRAM Address 12 EXTA13 SRAM Address 13 EXTA14 SRAM Address 14 EXTA15 SRAM Address 15 EXTA16 SRAM Address 16 EXTA17 SRAM Address 17 EXTA18 SRAM Address 18 EXTA19 SRAM Address 19 EXTD0 SRAM Data 0 EXTD1 SRAM Data 1 EXTD2 SRAM Data 2 EXTD3 SRAM Data 3 EXTD4 SRAM Data 4 EXTD5 SRAM Data 5 EXTD6 SRAM Data 6 EXTD7 SRAM Data 7 NV_OE# SRAM Output Enable NV_WE# SRAM Write Enable NV_CS# SRAM Chip Select
7. EXTERNAL MEMORY
The system designer has the option of using external memory. The external memory interface is implemented with two controllers. The SRAM controller allows the DSP to autoboot from a parallel FLASH or EEPROM device. The SRAM and SDRAM controllers are used to extend the data memory of the DSP during runtime. A system can use a FLASH/EEPROM device for autoboot, and either SRAM or SDRAM for runtime memory. The application user's guide for a particular code load will inform the system designer if memory is required, and will specify the memory type and speed. If no mention is made of external memory, then external memory is not required for that application. The SDRAM interface is not available on the 100-pin device. The signals for the external memory interface are listed in Table 11. and Table 12. For both controllers, memory access speed is controlled by the DSP clock setting which is constrained by the application code. The SRAM interface is capable of in-system programming a FLASH device. Wait states are available to support slower FLASH/EEPROM and SRAM devices. The SRAM interface supports 1Mx8 addressable space. We recommend 12nS or better SRAM for optimal performance. The SDRAM interface supports 16Mbit parts organized as 512k x 16bits x 2 banks which yields a 1Mx16 addressable space. The burst
144-Pin Number 73 74 75 76 67 66 65 63 62 60 72 56 55 54 53 52 49 47 46 71 34 35 36 37 38 40 43 44 31 71 32
100-Pin Number 51 52 53 54 46 45 44 43 42 41 50 40 39 38 37 36 35 34 33 N/A 23 24 25 26 27 28 31 32 21 N/A 22
Table 11. SRAM Interface Pins
Pin Name SD_DATA0 SD_DATA1 SD_DATA2 SD_DATA3 SD_DATA4 SD_DATA5 SD_DATA6 SD_DATA7 SD_DATA8 SD_DATA9 SD_DATA10 SD_DATA11 SD_DATA12 SD_DATA13 SD_DATA14 Pin Description SDRAM Data 0 SDRAM Data 1 SDRAM Data 2 SDRAM Data 3 SDRAM Data 4 SDRAM Data 5 SDRAM Data 6 SDRAM Data 7 SDRAM Data 8 SDRAM Data 9 SDRAM Data 10 SDRAM Data 11 SDRAM Data 12 SDRAM Data 13 SDRAM Data 14 144-Pin Number 34 35 36 37 38 40 43 44 56 55 54 53 52 49 47
Table 12. SDRAM Interface Pins 69
Pin Name SD_DATA15 SD_ADDR0 SD_ADDR1 SD_ADDR2 SD_ADDR3 SD_ADDR4 SD_ADDR5 SD_ADDR6 SD_ADDR7 SD_ADDR8 SD_ADDR9 SD_ADDR10
Pin Description SDRAM Data 15 SDRAM Address 0 SDRAM Address 1 SDRAM Address 2 SDRAM Address 3 SDRAM Address 4 SDRAM Address 5 SDRAM Address 6 SDRAM Address 7 SDRAM Address 8 SDRAM Address 9 SDRAM Address 10 SD_DQM0 SDRAM Data Mask Output0 SD_WE# SDRAM Write Enable SD_CAS# SDRAM Column Address Strobe SD_RAS# SDRAM Row Address Strobe SD_CS# SDRAM Chip Select SD_BA SDRAM Bank Select SD_DQM1 SDRAM Data SD_CLK_IN SDRAM Clock Input SD_CLK_OUT SDRAM Clock Output SD_CLK_EN SDRAM Clock Enable
144-Pin Number 46 73 74 75 76 67 66 65 63 62 60 72
Kickstarting the downloaded DSPC application code.
Mnemonic SRAM_CONTROLLER_TIMING Hex Message 0x8100000F 0x00000aaa
0xaaa = 0www wwrr rrre (in binary) w = SRAM_FLASH_WR_CYCLE variable found in the SRAM Switching characteristics table in Section 1.19. r = SRAM_FLASH_RD_CYCLE variable found in the SRAM Switching characteristics table in Section 1.19. e = SRAM Enable/Disable = 0/1.
Default, aaa = 0x000 Table 13. SRAM Controller Timing Hex Message 0x81000017 0xaaaabbbe
39 37 78 77 68 71 45 61 59 64
Mnemonic SDRAM_CONFIG
aaaa = Auto refresh setting. For example for a 16 S refresh period and a DCLK of 86 Mhz the value programmed should be: 16X10-6 X 86X106 = 0x(1376) = 0x0560 bbb = Mode register setting. These bits set the 12 least significant bits in the mode register. The bits are to the following by default: bits(2..0) = 011 = Burst length 8. bit3 = 0 = Sequential Burst Type. bits(6..4) = 010 = CAS latency of 2. bits(8..7) = 00 = Mode Register Set. bit9 = 0 = Write Burst. bit(12..10) = 000 = reserved e = SDRAM Enable/Disable =0001/0000.
Default, 0xaaaabbbe = 0x0560008c0 Table 14. SDRAM Config Register
Table 12. SDRAM Interface Pins
length is fixed to 8. We recommed SDRAM with a CAS latency of 2 for optimal performance. The refresh rate and the mode register of the SDRAM must be set before Kickstart. Refer to Table 14, "SDRAM Config Register," on page 70 for details on the SDRAM config register. The SDRAM is initialized after Kickstart.
7.1 Configuring SRAM Timing Parameters
Since not all SRAM manufacturers conform to the exact same timing specifications, it is necessary to configure the DSP to match the timing specifications of the particular SRAM that is used in your design. This message must be sent before
70
8. BOOT PROCEDURE
In this section the process of booting and downloading to the CS49400 will be covered as well as how to perform a soft reset. There are two ways to boot the DSP: * Host Controlled MasterBoot * Host Boot Via DSPC Each of these boot procedures will be described in detail with pseudocode. The flow charts use the following messages: * Write-C_* Write to DSPC * * * Read-C_* Read from DSPC Write-AB_* Write to DSPAB Read-AB_* Read from DSPAB
Note:When reading from DSPAB the host must wait for FINTREQ to fall before starting the read cycle. When reading from DSPC the host must wait for INTREQ to fall before starting the read cycle. Note:The * can be replaced by SPI, INTEL, or MOT depending on the mode of host communication. For each case the general download algorithm is the same.
C_SLAVE_MODE C_MASTER_BOOT_FLASH 1110 wwww wrrr rrAA c b
0x80 00 00 00 0xEw cb AA AA
AAAA AAAA AAAA AAAA Where w = SRAM_FLASH_WR_CYCLE variable found in the SRAM Switching characteristics table in Section 1.19. r = SRAM_FLASH_RD_CYCLE variable found in the SRAM Switching characteristics table in Section 1.19. A = 18-bit start address/4
Table 16. Boot Write Messages for DSPC (Continued) MNEMONIC C_BOOT_START C_BOOT_SUCCESS C_APP_START C_BOOT_ERROR_CHECKSUM INVALID_BOOT_TYPE VALUE 0x00 00 00 01 0x00 00 00 02 0x00 00 00 04 0x00 00 00 FF 0x00 00 00 FE
Table 16, and Table 17 define the boot write messages and boot read messages in mnemonic and actual hex value for DSPAB and DSPC. These messages will be used in the boot sequence
MNEMONIC AB_APP_START AB_APP_FAILURE VALUE 0x03 0xF0
Table 17. Boot Read Messages from DSPC
8.1 Host Controlled Master Boot
A host controlled master boot is a sequence where a host instructs the DSP to load application code into itself from external memory. External memory can either be FLASH or SPI EEPROM. The flow chart given in Figure 52, "Host Controlled Master Boot (Downloading both a DSPAB Application Code and a DSPC Application Code)" on page 72 demonstrates the interaction required by the microcontroller when placing the DSP into a host controlled master mode. 1) A download sequence is started when the host holds the mode pins appropriately (UHS[2:0] and FHS[1:0]) and toggles RESET. 2) The host must then send the C_MASTER_SOURCE_MODE boot message
71
Table 15. Application Messages from DSPAB MNEMONIC C_RESERVED C_SOFT_RESET VALUE 0x00 00 00 00 0x40 00 00 00
Table 16. Boot Write Messages for DSPC
STAR T
R ESET(LOW ) R EAD-C_*(C_ MESSAGE)
RESET(H IGH) M SG== C _BOOT_SU CC ESS W AIT ?? u S Y W RITE-C_*(C_SOFT_ RESET) N EXIT(ER ROR)
W RITE-C_* (C_M ASTER_SOU RC E_MODE)
IN TR EQ LOW ?
N
TIMEOUT A FTER (10 m S)
INTREQ LOW ?
N
TIMEOU T AFTER (10 mS)
Y Y READ -C _*(C _ME SSAGE) RE AD-C_*(C_M ESSAGE)
MSG ==C _BOOT_START Y RELEAS E C ON TR OL OF B US
N EX IT(ERR OR )
MSG== C_ APP_START Y W R ITE-C_*(C_ HW _ CONFIG_MSG, MS G_ SIZE)
N
EXIT(ER ROR)
N IN TR EQ LOW ? Y R EAD-C_ *(C_ MESSAGE)
TIM EOUT AFTE R (500 m S)
W RITE-C _*(C_SW _CON FIG_M SG, MS G_ SIZE)
W RITE-C_*(KICKS TAR T, MS G_ SIZE)
C _APPL ICATION_R UN NIN G MSG== C_B OOT_SUC CES S Y W RITE-C_* (C_M ASTER_SOU RC E_MODE) N EXIT(ER ROR) FINTREQ LOW ? HOUTRD Y HI? Y R EAD-AB_*(A B_MESS AGE ) IN TR EQ LOW ? N TIMEOUT A FTER (10 m S) MSG== AB_ APP_START Y W R ITE -AB_*(AB_H W _C ONFIG_ MSG, MS G_ SIZE) EX IT(ERR OR ) W RITE-AB_*(AB_SW _ CONFIG_MSG, MS G_ SIZE) N EXIT(E RROR ) N TIMEOUT AFTER (10 mS )
Y RE AD-C_*(C_M ESSAGE)
MSG ==C _BOOT_START Y RELEAS E C ON TR OL OF B US
N
W RITE-AB_*(KICKSTAR T, MS G_ SIZE) N INTREQ LOW ? Y TIM EOUT AFTE R (500 m S) AB_APPLICATION_R UN NIN G
Figure 52. Host Controlled Master Boot (Downloading both a DSPAB Application Code and a DSPC Application Code)
72
to DSPC. The supported messages are described in Table 16. This message tells DSPC where to get the DSPAB image from. Currently the C_MASTER_BOOT_FLASH message is supported and allows booting from external byte-wide flash or eprom. 3) If the initialization was successful DSPC sends out the C_BOOT_START message and the host must proceed to step 4. If initialization fails the host must re-try steps 1 through 3 and if failure is met again, the communication timing and protocol should be inspected. 4) After receiving the C_BOOT_START message, the host must release control of the communication interface and wait for INTREQ to go low.
Note: DSPC will autoboot DSPAB. After this DSPC will release control of the communication interface, but only when in SPI Master Boot Mode.
to go low.
Note:DSPC will autoboot DSPC. After this DSPC will release control of the communication interface, but only when in SPI Master Boot Mode.
9) The end of the .ULD file contains a four byte checksum. If the checksum is good after the download, DSPC will send a C_BOOT_SUCCESS message to the host. If the checksum was bad, DSPC responds with the C_BOOT_ERROR_CHECKSUM message and waits for a hard reset. 10) After reading out the C_BOOT_SUCCESS message, the host must send the C_SOFT_RESET message which will cause the application code to reset and allow the downloaded application to run. 11) If the soft reset was successful, DSPC sends out a C_APP_START message the host can proceed to step 12. If DSPC does not send an the application start message, the host must retry the whole procedure again. 12) Next the host can send hardware and software configuration messages for DSPC. 13) At this point the application code on DSPC is running and the host needs to configure DSPAB. 14) The host must read the AB_APP_START message from DSPAB. If DSPAB does not send an the application start message the host must re-try the whole procedure again, starting with step 1. 15) The host must send hardware and software configuration messages for DSPAB, ending with the kickstart message. 16) At this point the application code on DSPAB is running.
Note: Hardware configuration messages are used to define the behavior of the DSP's audio ports. A more detailed description of the different hardware configurations can be found
5) The end of the .ULD file contains a three byte checksum. If the checksum is good after the download, DSPC will send a C_BOOT_SUCCESS message to the host. If the checksum was bad, DSPC responds with the C_BOOT_ERROR_CHECKSUM message message and waits for a hard reset. 6) After reading out the C_BOOT_SUCCESS message, the host must send a second C_MASTER_SOURCE_MODE boot message to DSPC. This messages tells DSPC where the to get image for DSPC. 7) If the initialization was successful DSPC sends out the C_BOOT_START message and the host must proceed to step 8. If initialization fails the host must re-try step 6. If failure is met again, the communication timing and protocol should be inspected. 8) After receiving the C_BOOT_START message, the host must release control of the communication interface and wait for INTREQ
73
in the Section 10 "Hardware Configuration" on page 78. Note: The software configuration messages are specific to each application. The application code user's guide for each application provides a list of all pertinent configuration messages. Writing the KICKSTART message to DSPAB begins the audio decode process.
the host should re-try step 6. If failure is met again, the communication timing and protocol should be inspected. 8) After receiving the C_BOOT_START message, the host should write the downloadable image for DSPC. 9) The host must wait for INTREQ to go low and read the message from DSPC. 10) After reading out the C_BOOT_SUCCESS message. The host must send the C_SOFT_RESET message which will cause the application code to reset and allow the downloaded application to run. 11) If the soft reset was successful, DSPC sends out a C_APP_START message the host can proceed to step 8. If DSPC does not send an the application start message, the host must re-try the whole procedure again. 12) Next the host can send hardware and software configuration messages for DSPC. 13) At this point the application code on DSPC is running and the host needs to configure DSPAB. 14) The host must read the AB_APP_START message from DSPAB. If DSPAB does not send an the application start message the host must re-try the whole procedure again, beginning at setp 1. 15) The host must send hardware and software configuration messages for DSPAB. 16) At this point the application code on DSPAB is running.
Note: Hardware configuration messages are used to define the behavior of the DSP's audio ports. A more detailed description of the different hardware configurations can be found in the Section 10 "Hardware Configuration" on page 78. Note: The software configuration messages are specific to each application. The application code user's guide for each application provides
8.2 Host Boot Via DSPC
A host controlled boot via DSPC is a sequence where the host boots DSPAB and DSPC through DSPC with two separate images (.ULD files). Figure 53, "Host Boot Via DSPC" on page 75 demonstrates the interaction required by the microcontroller. 1) A download sequence is started when the host holds the mode pins appropriately (UHS[2:0] and FHS[1:0]) and toggles RESET. 2) The host must then send the C_SLAVE_MODE boot message to DSPC. This causes DSPC to initialize itself. 3) If the initialization was successful DSPC sends out a C_BOOT_START message. The host should proceed to step 4. If initialization fails, the host should re-try steps 1 through 3 and if failure is met again, the communication timing and protocol should be inspected. 4) After receiving the C_BOOT_START message, the host should write the downloadable image for DSPAB(.ULD file) to DSPC. 5) The host must wait for INTREQ to go low and read the message from DSPC. 6) After reading out the C_BOOT_SUCCESS message, the host must then send the C_SLAVE_MODE message to DSPC once more. This causes DSPC to initialize itself and get ready to accept a stream. 7) If the initialization was successful DSPC sends out a C_BOOT_START message. The host should proceed to step 8. If initialization fails,
74
STAR T
RE SET(LO W ) RE AD -C _*(C _MES SA GE )
W A IT 10 uS MSG== C _B OOT_SUC CE SS R ESE T(HIGH) N EXIT(ER R OR )
W RITE -C _* (C_SLAVE _MOD E)
W R ITE-C_*(C_SOFT_RE SET)
INTR EQ LO W ?
N
TIME OUT AFTER (5 m S)
IN TR EQ LOW ?
N
TIME OU T A FTER (5 m S )
Y Y R EA D-C_*(C_ME SS AGE) RE AD-C_*(C_MES SAGE )
MSG ==C_BOOT_S TA RT Y W R ITE-C_*(.U LD FILE ,FILE S IZE) for DS P AB
N EXIT(ER ROR )
MSG== C_A PP_S TA R T Y W RITE -C _*(C_H W _C ONFIG_MSG, MSG_S IZE)
N
E XIT(ERR OR )
N INTR EQ LO W ?
TIME OU T A FTER (5 mS )
W R ITE-C_*(C_SW _CON FIG_MSG, M SG_SIZE )
Y RE AD -C _*(C _M ESSA GE)
W R ITE-C_*(KIC KS TA RT, M SG_SIZE )
C_AP PLIC ATION _R UN NIN G Y MSG== C_BOOT_S UC CE SS N EXIT(E RR OR) FINTR EQ LOW ? HOU TR DY H I? W RITE -C _* (C_SLAVE _MOD E) Y REA D -AB _*(A B_ME SSA GE) N TIME OUT A FTER (5 m S )
INTR EQ LO W ?
N
TIME OUT AFTER (5 m S)
MSG== AB _AP P_STA RT Y
N EXIT(ER R OR)
Y RE AD-C_*(C_MES SAGE )
W RITE -AB _*(AB_H W _C ON FIG_MSG, M SG_SIZE ) MSG ==C_BOOT_S TA RT Y W R ITE-C_*(.U LD FILE ,FILE S IZE) for D SP C W RITE-AB_*(KIC K START, M SG_SIZE ) N EXIT(ER ROR ) W R ITE-A B_*(AB _SW _CON FIG_MS G, M SG_SIZE )
N INTR EQ LO W ?
TIME OU T A FTER (5 mS )
AB_AP PLIC ATION _R UN NIN G
Y
Figure 53. Host Boot Via DSPC
75
a list of all pertinent configuration messages. Writing the KICKSTART message to DSPAB begins the audio decode process.
and FHS[1:0]) and toggles RESET. 2) The host must send the C_SOFT_RESET message to DSPC. This causes the application code on DSPAB and DSPC to reset and allow the downloaded application to run. 3) If the soft reset was successful, DSPC sends out a C_APP_START message the host can proceed to step 4. If DSPC does not send an the application start message, the host must re-try the whole procedure again. 4) The host can send hardware and software configuration messages for DSPC. 5) At this point the application code on DSPC is running and the host needs to configure DSPAB. 6) Next the host must wait for FINTREQ to go low and read the AB_APP_START message from DSPAB. If DSPAB does not send an the application start message the host must re-try the whole procedure again, beginning from step 1. 7) The host must send hardware and software configuration messages for DSPAB. 8) At this point the application code on DSPAB is running.
9. SOFT RESETTING THE CS49400
Soft resetting the CS49400 uses a combination of software and hardware. This method of resetting the DSP is usually referred to as a "soft reset" even though it involves toggling the reset pin due to the fact that a soft reset message is sent to the DSP. To soft reset the device, a previous application code must have been downloaded without power cycling the DSP. Figure 54, "Host Controlled Master Softreset" on page 77 describes the soft reset procedure. The main purpose behind a soft reset is to take advantage of the fact that all AC-3 based codes can accept both AC-3 compressed data as well as PCM data. This allows for a the host to reconfigure the AC-3 application code for PCM or AC-3 without having to completely redownload the same application code.
9.1 Host Controlled Master Soft Reset
This reset procedure is used to restart the application code that has already been loaded on the DSP. All writes and reads with the CS49400 should follow the protocol given in Section 8 "Boot Procedure" on page 71. 1) A Soft Reset sequence is started when the host holds the mode pins appropriately (UHS[2:0]
76
S TA RT
RES ET(LOW )
W AIT 10 uS
RES ET(HIGH)
W RITE-C_*(C_S OFT_RES ET)
INTRE Q LOW ?
N
TIM EOUT AFTE R (5 m S)
N FINTREQ LOW ?
TIME OUT A FTE R (5 m S )
Y REA D-C_*(C_ME SS AGE)
Y RE A D-AB _*(AB _M E SS AGE)
MS G== C_AP P_S TA RT Y W RITE -C_*(C_HW _CONFIG_M S G, MSG_S IZE)
N
E XIT(ERROR)
M SG== A B_APP _S TART Y
N E XIT(E RROR)
W RITE-AB _*(A B_HW _CONFIG_M S G, MS G_SIZE)
W RITE -C_*(C_S W _CONFIG_MS G, MSG_S IZE)
W RITE-AB _*(A B_S W _CONFIG_MS G, MS G_SIZE)
W RITE -C_*(K ICK START, MSG_S IZE)
W RITE-A B_*(K IC KS TA RT, MS G_SIZE)
C _A PP LICA TION_RUNNING
AB _AP PLICATION _RUNNING
Figure 54. Host Controlled Master Softreset 77
10. HARDWARE CONFIGURATION
After download or soft reset, and before kickstart, the host has the option of changing the default hardware configuration. (Please see the Audio Manager in the Application Messaging Section of any Application Code User's Guide for more information on kickstarting.) Hardware configuration messages are used to physically reconfigure the hardware of the audio decoder, as in enabling or disabling address checking for the serial communication port. Hardware configuration messages are also used to initialize the data type (i.e., PCM or compressed) and format (e.g., I2S, left justified, etc.) for digital data inputs, as well as the data format and clocking options for the digital output port. In general, the hardware configuration can only be changed immediately after download or after soft reset and before kickstart. However, some applications provide the capability to change the input ports without affecting other hardware configurations, after sending a special Application Restart message. (Please see the Audio Manager in any Application Code User's Guide to determine whether the Application Restart message is supported.)
11.1 Digital Audio Formats
This subsection will describe some common audio formats that the CS49400 supports. It should be noted that the input ports use up to 24-bit PCM resolution and 16-bit compressed data word lengths. The output port of the CS49400 provides up to 24-bit PCM resolution.
11.1.1 I2S
Figure 55, "I2S Format" on page 79 shows the I2S format. For I2S, data is presented most significant bit first, one FSCLKN1 delay after the transition of FLRCLKN1, and is valid on the rising edge of FSCLKN1. For the I2S format, the left subframe is presented when FLRCLKN1 is low; the right subframe is presented when FLRCLKN1 is high. FSCLKN1 is required to run at a frequency of 48Fs or greater on the input ports.
11.1.2 Left Justified
Figure 56, "Left Justified Format (Rising Edge Valid SCLK)" on page 79 shows the left justified format with a rising edge FSCCLK. Data is presented most significant bit first on the first FSCLKN1 after an FLRCLKN1 transition and is valid on the rising edge of FSCLKN1. For the left justified format, the left subframe is presented when FLRCLKN1 is high and the right subframe is presented when FLRCLKN1 is low. The left justified format can also be programmed for data to be valid on the falling edge of FSCLKN1. FSCLKN1 is required to run at a frequency of 48Fs or greater on the input ports.
11. DIGITAL INPUT AND OUTPUT DATA FORMATS
The CS49400 supports a wide variety of data input and output data formats through various input and output ports. Hardware availability is entirely dependent on whether the software application code being used supports the required mode. This data sheet presents most of the modes available with the CS49400 hardware. This does not mean that all of the modes are available with any particular piece of application code. The Application Code User's Guide for the particular code being used should be referenced to determine if a particular mode is supported. In addition if a particular mode is desired that is not presented, please contact your local FAE as to its availability.
11.2 Digital Audio Input Port
The digital audio input port (DAI) on DSPAB, is used for both compressed and PCM digital audio data input. In addition this port supports a special clocking mode in which a clock can be input to directly drive the internal 33 bit counter. Table 18, "Digital Audio Input Port," on page 79 shows the
78
pin names, mnemonics and pin numbers associated with the DAI.
Pin Name Pin Description 144-Pin 100-Pin Package, Package, Pin Pin Number Number 131 84 134 81
Pin Name
Pin Description
FSDATAN1 FSCLKN1 FSTCCLK2 FLRCLKN1
Serial Data In Serial Bit Clock Secondary STC Clock Frame Clock
FSDATAN2 Serial Data In CMPDAT Compressed Data In FSCLKN2 Serial Bit Clock CMPCLK FLRCLKN2 Frame Clock CMPREQ Data Request Out
100-Pin 144-Pin Package, package, Pin Pin Number Number 118 79
111 117
78 80
119
85
Table 19. Compressed Data Input Port
Table 18. Digital Audio Input Port
The DAI is fully configurable including support for I2S and left-justified formats. DAI is programmed for slave clocks, where FLRCLKN1 and FSCLKN1 are inputs. All DAI configuration messages must be sent to DSPAB.
11.4 Input Data Hardware Configuration for CDI and DAI on DSPAB
Both data format (I2S, Left Justified) and data type (compressed or PCM) are required to fully define the input port's hardware configuration. The DAI and the CDI are configured by the same group of messages since their configurations are interrelated. The naming convention of the input hardware configuration is as follows: INPUT A B C where A, B, C and are the parameters used to fully define the input port. The parameters are defined as follows: A - Data Type B - Data Format C - SCLK Polarity
11.3 Compressed Data Input Port
The compressed data input port (CDI) on DSPAB can be used for both compressed and PCM data input. Table 19 shows the mnemonic, pin name, and pin number of the pins associated with the CDI port on the CS49400. The CDI port is fully configurable for all data formats including: I2S, left-justified and multichannel formats. FLRCLKN2 and FSCLKN2 on the CDI port are programmed to be inputs. All CDI configuration messages must be sent to DSPAB.
FLRCLKN1 FSCLKN1
FSDATAN1 MSB LSB Left
Right
MSB
LSB
Figure 55. I2S Format
FLRCLKN1 FSCLKN1
FSDATAN1 MSB
Left
Right
LSB
MSB
LSB
MSB
Figure 56. Left Justified Format (Rising Edge Valid SCLK) 79
The following tables show the different values for each parameter as well as the hex message that needs to be sent. When creating the hardware configuration message, only one hex message should be sent per parameter. It should be noted that the entire B parameter hex message must be sent, even if one of the input ports has been defined as unused by the A parameter.
A Value Data Type 0 DAI - PCM (default) CDI - Compressed Hex Message 0x800210 0x3FBFC0 0x800110 0x80002C 0x800210 0x3FBFC0 0x800110 0xC0002C 0x800210 0x3FBFC0 0x800110 0x800020
B Value Data Format 1 PCM - Left Justified 24-bit
Hex Message 0x800217 0x8080FF Compressed - Left Justified 0x80021A 16-bit 0x8080FF 0x800117 (Compressed means any type of compressed data such as IEC61937- 0x001000 0x80011A packed AC-3, DTS, MPEG Multichannel, AAC or MP3 elementary 0x001800
stream data from a DVD or IEC60958packed elementary stream DTS data from a DTS-CD)
Table 21. Input Data Format Configuration (Input Parameter B) (Continued) SCLK Polarity (Both CDI and Hex C Value DAI Port) Message 0 Data Clocked in on Rising 0x800217 (default) Edge 0xFFFFDF 0x80021A 0xFFFFDF 1 Data Clocked in on Falling 0x800117 Edge 0x000020 0x80011A 0x000020 Table 22. Input SCLK Polarity Configuration (Input Parameter C)
1
DAI - PCM and Compressed CDI - Unused
2
DAI - Unused CDI - PCM
Table 20. Input Data Type Configuration (Input Parameter A) Hex B Value Data Format Message 0 PCM - I2S 24-bit 0x800217 (default) 0x8080FF Compressed - I2S 16-bit 0x80021A Compressed means any type of com- 0x8080FF 0x800117 pressed data such as IEC61937packed AC-3, DTS, MPEG Multichan- 0x011100 nel, AAC or MP3 elementary stream 0x80011A data from a DVD or IEC60958-packed 0x011900
elementary stream DTS data from a DTS-CD)
11.4.1
Input Configuration Considerations
Table 21. Input Data Format Configuration (Input Parameter B)
1) 24-bit PCM input requires at least 24 SCLKs per sub-frame. The DSP always uses 24-bit resolution for PCM input. Systems having less than 24-bit resolution will not have a problem as the extra bits taken by the DSP will be under the noise floor of the input signal for left justified and I2S formats. For compressed input, data is always taken in 16 bit word lengths. 2) If the clocks to the audio ports are known to be corrupted, such as when a S/PDIF receiver goes out of lock, the DSP should undergo an application restart (if applicable), soft reset, or hard reset. All three actions will result in the input FIFO being reset. Failure to do so may result in corrupted data being latched into the
80
input FIFO and may result in corrupted data being heard on the outputs. Corruption is only an issue when PCM data is being delivered. When compressed data is being delivered, there are sync words embedded in the data stream to which the DSP can lock. Certain application codes that are capable of processing PCM may now have a special feature called "PCM Robustness" which prevents the corruption described above, but you should still use a FIFO reset to ensure good data.
be sent to DSPC to configure and enable the SAI port.
D Value Data Type 0 PCM - I2S 24-bit Hex Message 0x81000010 0x00000001 0x81000011 0x00011701 0x81000012 0x00004E4F 0x81000010 0x00000001 0x81000011 0x00001600 0x81000012 0x00005E4F
1
PCM - Left Justified 24-bit
11.5 Serial Audio Input
The Serial Audio Input (SAI) provides four stereo inputs to DSPC. The SAI can be used to postprocess PCM data from a multichannel Super Audio CD input or DVD Audio/Video input via high-performance A/Ds. Table 19 shows the
Pin Name Pin Description 144-Pin 100-Pin Package, Package, Pin Pin Number Number 86 60 85 59 79 55 80 56 81 57 82 58
Table 24. SAI Data Type Configuration (Input Parameter D)
11.6 Digital Audio Output Port
The Digital Audio Output port (DAO) can transmit up to 16 channels of PCM data that are fully configurable into standard audio format. It also has two IEC60958 pins that provide CMOS level bi phase encoded outputs. Table 25 shows the signals associated with the DAO. As with the input ports the clocks and data are fully configurable via hardware configuration. All DAO configuration messages must be sent to DSPC.
Pin Name MCLK SCLK1 Pin Description 144-Pin Number 99 98 87 92 100-Pin Number 68 67 61 64
SCLKN LRCLKN SDATAN3 SDATAN2 SDATAN1 SDATAN0
Serial Bit Clock Frame Clock Serial Data In 3 Serial Data In 2 Serial Data In 1 Serial Data In 0
Table 23. Serial Audio Input Port
Master Clock Serial Bit Clock for AUDATA 4-7 Frame Clock for AUDATA 4-7
mnemonic, pin name and pin number of the pins associated with the SAI port on the CS49400. The SAI has 4 stereo data inputs that are fully configurable including support for I2S, leftjustified and multichannel formats. The SAI port operates in slave mode only with LRCLKN and SCLKN as inputs. Processing on the CDI and DAI ports must be disabled before the SAI port is enabled. Either the input D0 or D1 message must
LRCLK1
AUDATA7,X Serial Data Out 7, MT958B IEC60958 Transmitter AUDATA6 AUDATA5 AUDATA4
Serial Data Out 6 Serial Data Out 5 Serial Data Out 4
93 94 102
65 66 71
Table 25. Digital Audio Output Port
81
Pin Name SCLK0 LRCLK0
Pin Description
144-Pin Number 104 108 106
100-Pin Number 72 75 73
different MCLK frequencies. (All values are expressed in terms of the sampling frequency, Fs.)
MCLK (Fs) SCLK (Fs) 32 48 64 128 256 512
Serial Bit Clock for AUDATA 0-3 Frame Clock for AUDATA 0-3
128 384 256
107 109 110 74 76 77
X X X X X
X X X X X X X X X
AUDATA3,X Serial Data Out 3, MT958A IEC60958 Transmitter AUDATA2 AUDATA1 AUDATA0
Serial Data Out 2 Serial Data Out 1 Serial Data Out 0
512
Table 26. MCLK/SCLK Master Mode Ratios
Table 25. Digital Audio Output Port (Continued)
MCLK is the master clock and is firmware configurable to be either an input or an output. If MCLK is to be used as an output, the internal PLL must be used. As an output MCLK can be configured to provide a 128Fs, 256Fs, or 512Fs clock, where Fs is the output sample rate. SCLK0 is the bit clock used to clock data out on AUDATA0, AUDATA1, AUDATA2 and AUDATA3. LRCLK0 is the data framing clock whose frequency is typically equal to the sampling frequency for AUDATA0, AUDATA1, AUDATA2 and AUDATA3. SCLK1 is the bit clock used to clock data out on AUDATA4, AUDATA5, AUDATA6 and AUDATA7. LRCLK1 is the data framing clock whose frequency is typically equal to the sampling frequency for AUDATA4, AUDATA5, AUDATA6 and AUDATA7. LRCLK0, LRCLK1, SCLK0 and SCLK1 can be configured as either inputs (Slave) or outputs (Master). A valid MCLK is required for all output modes. When LRCLK0, LRCLK1, SCLK0 and SCLK1 are configured as outputs, they are derived from MCLK. Whether MCLK is configured as an input or an output, an internal divider from the MCLK signal is used to produce LRCLK0, LRCLK1, SCLK0 and SCLK1. The ratios shown in Table 26 give the possible SCLK values for
Both the AUDAT0 and AUDAT4 Digital Audio Output porst are configurable to provide output for two, four, or six channels of PCM data. AUDATA1, AUDATA2, AUDATA3, AUDATA5, AUDATA6 and AUDATA7 are only capable of outputting two channels of PCM data. Typically AUDATA[0:7] are configured for outputting either left justified or I2S formatted data. In a standard 5.1 channel AVR, AUDATA0, AUDATA1 and AUDATA2 are used to output the six discrete channels (Left, Center, Right, Left Surround, Right Surround, and Subwoofer). AUDATA3 can be used with AUDATA0, AUDATA1 and AUDATA2 to support 7.1 output. Alternatively AUDATA3 and AUDATA7 can be used for dual zone support. AUDATA3 and AUDATA7 are multiplexed with the XMT958 output so only one can be used at any one time. Please refer to AN208, AN209 and their corresponding appendices for information about which output modes are supported, as this is specific to each application code.
11.6.1 S/PDIF Outputs
Both AUDATA3 and AUDATA7 digital audio output ports are unique, in that they can serve either an additional output for I2S or Left Justified PCM data OR as IEC60959 bi-phase mark encoded data S/PDIF transmitters. When either of these ports are configured as a S/PDIF transmitter, the MCLK required for such functionality can be provided from either the internally locked PLL or from an
82
MCLK input. All consumer channel status information can be included in the S/PDIF stream, provided that the particular application code supports this functionality. When configured as a S/PDIF transmitter, the designer should understand that in order for these ports to be fully IEC60958 compliant, the outputs would need to be buffered through an RS422 device or an optocoupler as its outputs are only CMOS driven.
11.7 Output Data Hardware Configuration
The DAO naming convention is as follows: OUTPUT A B C D, where the parameters are defined as: A - DAO Mode (Master/Slave for LRCLK0, LRCLK1, SCLK0 and SCLK1) B - Data Format C - MCLK, SCLK, LRCLK Frequency The following tables show the different values for each parameter as well as the hex message that needs to be sent. When creating the hardware configuration message, only one hex message should be sent per parameter.
DAO Modes (LRCLK and SCLK) 0 MCLK - Slave (default) SCLK0 - Slave LRCLK0 - Slave SCLK1 - Slave LRCLK1 - Slave 1 MCLK - Slave SCLK0 - Master LRCLK0 - Master SCLK1 - Master LRCLK1 - Master A Value Hex Message 0x81800003 0x00101000
DAO Data Format Of AUDATA0, 1, 2 (or B AUDATA0 for Multichannel Hex Value Modes) Message 0 I2S 24-bit 0x81800003 (default) (Configuration of AUDATA3 as 0xFFFE3FFF S/PDIF (IEC60958) or Digital Audio 0x81400003 in the format of I2S or Left Justified is 0x0001C000 0x81000005 covered in AN209) 0x00101701 0x81000006 0x00100001 0x81000007 0x00100001 0x81000008 0x00100001 1 Left Justified 24-bit 0x81800003 0xFFFE3FFF (Configuration of AUDATA3 as S/PDIF (IEC60958) or Digital Audio 0x81400003 in the format of I2S or Left Justified is 0x0000C000 0x81000005 covered in AN209) 0x00101701 0x81000006 0x00100000 0x81000007 0x00100000 0x81000008 0x00100000 Table 28. Output Data Configuration Parameter B) Hex C Value SCLK/LRCLK Frequency Message 0 MCLK = 256 FS 0x81800003 (default) 0xFFFFFC7F 0x81400003 0x00000100 SCLK = MCLK / 4 = 64 FS 0x81000009 LRCLK = SCLK / 64 = FS 0x00077030 0x81800003 1 MCLK = 256 FS 0xFFFFFC7F 0x81400003 0x00000200 SCLK = MCLK / 2 = 128 FS 0x81000009 LRCLK = SCLK / 128 = FS 0x00177010 Table 29. Output SCLK/LRCLK Configuration (Parameter C)
0x81800003 0xFFEFFFFF
Table 27. Output Clock Configuration (Parameter A)
83
Hex C Value SCLK/LRCLK Frequency Message 2 MCLK = 256 FS 0x81800003 0xFFFFFC7F 0x81400003 0x00000300 SCLK = MCLK / 1 = 256 FS 0x81000009 LRCLK = SCLK / 256 = FS 0x00377000 0x81800003 3 MCLK = 512 FS 0xFFFFFC7F 0x81400003 0x00000100 SCLK = MCLK / 8 = 64 FS 0x81000009 0x00077070 LRCLK = SCLK / 64 = FS 4 MCLK = 128FS 0x81800003 0xFFFFFC7F 0x81400003 0x00000100 0x81000009 SCLK = MCLK / 2 = 64FS 0x00077010 LRCLK = SCLK / 64 = FS Table 29. Output SCLK/LRCLK Configuration (Parameter C) Hex Message 0x81800003 0xFFFBFFFF 0x81400003 0x00040000
This is the default configuration configuration message is required. DAI:Left Justified PCM and Compressed data CDI:Not used The above configuration corresponds to INPUT A1 B1
so
no
which corresponds to a configuration message of: 0x800210 0x3FBFC0 0x800110 0xC0002C 0x800217 0x8080FF 0x80021A 0x8080FF 0x800117 0x001000 0x80011A 0x001800 DAO:Left Justified slave mode (LRCLK, SCLK inputs) MCLK @ 256Fs SCLK @ 64Fs The above configuration corresponds to OUTPUT A0 B1 C0 D0 which has a configuration message of: 0x81800003 0xFFFE3FFF 0x81400003 0x0000C000 0x81000005 0x00101701 0x81000006 0x00100000 0x81000007
D Value SCLK Polarity 0 Data Valid on Rising Edge (default) (clocked out on falling) 1 Data Valid on Falling Edge (clocked out on rising)
Table 30. Output SCLK Polarity Configuration (Parameter D)
11.8 Creating Hardware Configuration Messages
The single hardware configuration message that must be sent to the CS49400 after download or soft reset should be a concatenation of the messages in the previous sections. The complete hardware configuration message should be created by taking a message for each parameter (where the default is not acceptable) and concatenating the messages together. No messages need to be sent if the default configuration for a particular parameter is acceptable. This example can be easily expanded to fit other system requirements. E.g. if the host system has this configuration: Address Checking: Disabled
84
0x00100000 0x81000008 0x00100000 Concatenating the messages together gives the hardware configuration message shown in Table 31, "Example Values to be Sent to DSPAB After Download or Soft Reset," on page 85, which should be sent to DSPAB after download or soft reset. Table 32, "Example Values to be Sent to DSPC After Download or Soft Reset," on page 85, which should be sent to DSPC after download or soft reset.
WORD# 1 VALUE 0x800210 WORD# 7 VALUE 0x80021A
2 3 4 5 6
0x3FBFC0 0x800110 0xC0002C 0x800217 0x8080FF
8 9 10 11 12
0x8080FF 0x800117 0x001000 0x80011A 0x001800
Table 31. Example Values to be Sent to DSPAB After Download or Soft Reset
WORD# 1 2 3 4
VALUE
WORD# 12 13 14 15
VALUE
0x81000006 0x00101700 0x81000006 0x00100000
0x81000007 0x00100000 0x81000008 0x00100000
Table 31. Example Values to be Sent to DSPAB After Download or Soft Reset
Table 32. Example Values to be Sent to DSPC After Download or Soft Reset
85
12.0 PIN DESCRIPTION 12.1 144-Pin LQFP Package Pin Layout
AUDATA5, GPIO29 AUDATA6, GPIO30 AUDATA7, XMT958B, GPIO31
LRCLK0 AUDATA2 AUDATA3, XMT958A HDATA3, GPIO3
HDATA4, GPIO4 AUDATA4, GPIO28 VSS2 VDD2
HDATA6, GPIO6 HDATA7, GPIO7
HDATA5, GPIO5
VDD1
105
100
90
NC2 LRCLK1
SCLK0
MCLK SCLK1
VSS1
85
SDATAN1, GPIO25 SDATAN2, GPIO26
SDATAN3, GPIO27 SD_CAS
NC4 SDATAN0, GPIO24
SCLKN, GPIO22
95
AUDATA1 AUDATA0 CMPCLK, FSCLKN2 HDATA2, GPIO2 VSS3 VDD3 HDATA1, GPIO1 HDATA0, GPIO0 CMPREQ, FLRCLKN2 CMPDAT, FSDATAN2 FLRCLKN1 WR, DS, GPIO10 RD, R/W, GPIO11 PLLVSS FILT2 FILT1 PLLVDD XTALO CLKIN, XTALI CLKSEL CS, GPIO9 A0, GPIO13 FSDATAN1 VDD4 VSS4 FSCLKN1, STCCLK2 SCS SCDIN VSS5 VDD5 A1, GPIO12 SCDOUT, SCDIO HINBSY, GPIO8 SCCLK UHS2, CS_OUT, GPIO17 RESET
80
75
SD_ADDR2 ,EXTA2 SD_ADDR1 ,EXTA1 SD_ADDR0, EXTA0
LRCLKN, GPIO23 NC3
SD_RAS SD_ADDR3 ,EXTA3
NC1
SD_ADDR10, EXTA10 110 70 SD_BA, EXTA19 VDDSD1 VSSSD1 SD_CS SD_ADDR4, EXTA4 SD_ADDR5, EXTA5 SD_ADDR6, EXTA6 SD_CLK_EN SD_ADDR7, EXTA7 SD_ADDR8, EXTA8 120 60 SD_CLK_IN SD_ADDR9, EXTA9 SD_CLK_OUT VDDSD2 VSSSD2 SD_DATA8, EXTA11 SD_DATA9, EXTA12 SD_DATA10, EXTA13 SD_DATA11, EXTA14 SD_DATA12, EXTA15 130 50 VDDSD3 VSSSD3 SD_DATA13, EXTA16 NC5 SD_DATA14, EXTA17 135 45 SD_DATA15, EXTA18 SD_DQM1 SD_DATA7, EXTD7 SD_DATA6, EXTD6 VDDSD4 140 40 VSSSD4 SD_DATA5, EXTD5 SD_DQM0 144 SD_DATA4, EXTD4 SD_DATA3, EXTD3
115 65
125 55
25
10
15
20
30
NV_OE, GPIO15 NV_CS, GPIO14 SD_WE
FDAT2 DBDA
DBCK FDAT1
SD_DATA0, EXTD0 SD_DATA1, EXTD1
UHS1, GPIO19 INTREQ
FDBCK
VDD7 VSS7 FDAT3 FDBDA
FDAT7 VDD6
FDAT6
TEST
35 SD_DATA2, EXTD2
UHS0, GPIO18
1
5
GPIO21
VSS6 FHS0, FWR, FDS FHS1, FRD, FR/W
FA1, FSCDIN GPIO20 FAO, FSCCLK
FDAT5 FDAT4
FHS2, FSCDIO, FSCDOUT
Figure 57. Pin Layout (144-Pin LQFP Package)
86
NV_WE, GPIO16
FCS FINTREQ
FDAT0
FILT1 PLLVDD XTALO
AUDATA1 AUDATA0 CMPCLK, FSCLKN2 VSS3 VDD3 80 CMPREQ, FLRCLKN2 CMPDAT, FSDATAN2 FLRCLKN1 PLLVSS FILT2 85
CLKIN, XTALI CLKSEL 90 FSDATAN1 FSCLKN1, STCCLK2 SCS SCDIN
VSS5 95 VDD5 SCDOUT, SCDIO SCCLK UHS2, CS_OUT, GPIO17 RESET 100 UHS0, GPIO18 75 LRCLK0 AUDATA2 AUDATA3, XMT958A SCLK0 AUDATA4, GPIO28 70 VSS2 VDD2 MCLK SCLK1 AUDATA5, GPIO29 65 AUDATA6, GPIO30 AUDATA7, XMT958B, GPIO31 VDD7 VSS7 15 FDBDA DBDA DBCK TEST NV_WE, GPIO16 20 NV_OE, GPIO15 NV_CS, GPIO14 EXTD0 EXTD1 EXTD2 25 50 EXTA10 EXTA19 VDDSD1 VSSSD1 EXTA4 45 EXTA5 EXTA6 EXTA7 EXTA8 EXTA9 40 EXTA11 EXTA12 EXTA13 EXTA14 EXTA15 35 EXTA16 EXTA17 EXTA18 EXTD7 EXTD6 30 VDDSD4 VSSSD4 EXTD5 EXTD4 EXTD3
12.2 100-Pin LQFP Package Pin Layout
1 UHS1, GPIO19 INTREQ FA1, FSCDIN FA0, FSCCLK 5 FHS2, FSCDIO, FSCDOUT VDD6 VSS6 FHS0, FWR, FDS FHS1, FRD, FR/W 10 FCS FINTREQ FDBCK
Figure 58. Pin Layout (100-Pin LQFP Package)
VSS1 VDD1 LRCLK1 60 SCLKN, GPIO22 LRCLKN, GPIO23 SDATAN0, GPIO24 SDATAN1, GPIO25 SDATAN2, GPIO26 55 SDATAN3, GPIO27 EXTA3 EXTA2 EXTA1 EXTA0
87
12.3 Pin Definitions
FILT1 -- Phase-Locked Loop Filter Connects to an external filter for the on-chip phase-locked loop. FILT2 -- Phase Locked Loop Filter Connects to an external filter for the on-chip phase-locked loop. CLKIN, XTALI -- External Clock Input/Crystal Oscillator Input CS49400 clock input. This pin accepts an external clock input signal that is used to drive the internal core logic. When in internal clock mode (CLKSEL == VSS), this input is connected to the internal PLL from which all internal clocks are derived. When in external clock mode (CLKSEL == VDD), this input is connected to the DSP clock. Alternatively, a 12.288 mhZ crystal oscillator can be connected between XTALI and XTALO. INPUT XTALO -- Crystal Oscillator Output Crystal oscillator output. OUTPUT CLKSEL -- DSP Clock Select This pin selects the internal source clock. When CLKSEL is low, CLKIN is connected to the internal PLL from which all internal clocks are derived. When CLKSEL is high, the PLL is bypassed and the external clock directly drives all input logic. INPUT FDAT7 -- DSPAB Bidirectional Data Bus FDAT6 FDAT5 FDAT4 FDAT3 FDAT2 FDAT1 FDAT0 In parallel host mode, these pins provide a bidirectional data bus to DSPAB. These pins have an internal pull-up. BIDIRECTIONAL - Default: INPUT FA0, FSCCLK -- Host Parallel Address Bit Zero or Serial Control Port Clock In parallel host mode, this pin serves as one of two address input pins used to select one of four parallel registers. In serial host mode, this pin serves as the serial control clock signal, specifically as the SPI clock input. INPUT
88
FA1, FSCDIN -- Host Address Bit One or SPI Serial Control Data Input In parallel host mode, this pin serves as one of two address input pins used to select one of four parallel registers. In SPI serial host mode, this pin serves as the data input. INPUT FHS1, FRD, FR/W -- Mode Select Bit 1 or Host Parallel Output Enable or Host Parallel R/W DSPAB control port mode select bit 1. This bit is one of 3 control port select bits that are sampled on the rising edge of RESET to determine the control port mode of DSPAB. In Intel parallel host mode, this pin serves as the active-low data bus enable input. In Motorola parallel host mode, this pin serves as the read-high/write-low control input signal. In serial host mode, this pin can serve as the external memory active-low data-enable output signal. BIDIRECTIONAL - Default: INPUT FHS0, FWR, FDS -- Mode Select Bit 0 or Host Write Strobe or Host Data Strobe DSPAB control port mode select bit 0. This bit is one of 3 control port select bits that are sampled on the rising edge of RESET to determine the control port mode of DSPAB. In Intel parallel host mode, this pin serves as the active-low data-write-input strobe. In Motorola parallel host mode, this pin serves as the active-low data-strobe-input signal. In serial host mode, this pin can serve as the external-memory active-low write-enable output signal. BIDIRECTIONAL - Default: INPUT FCS -- Host Parallel Chip Select, Host Serial SPI Chip Select In parallel host mode, this pin serves as the active-low chip-select input signal. In serial host SPI mode, this pin is used as the active-low chip-select input signal. INPUT FHS2, FSCDIO, FSCDOUT -- Mode Select Bit 2 or Serial Control Port Data Input and Output, Parallel Port Type Select DSPAB control port mode select bit 2. This bit is one of 3 control port select bits that are sampled on the rising edge of RESET to determine the control port mode of DSPAB. In SPI mode this pin serves as the data output pin. In parallel host mode, this pin is sampled at the rising edge of RESET to configure the parallel host mode as an Intel type bus or as a Motorola type bus. BIDIRECTIONAL - Default: INPUT FINTREQ -- Control Port Interrupt Request Open-drain interrupt-request output. This pin is driven low to indicate that the DSP has outgoing control data that should be read by the host. OPEN DRAIN I/O - Requires 3.3K Ohm Pull-Up FSCLKN1, STCCLK2 -- PCM Audio Input Bit Clock Digital-audio bit clock input. FSCLKN1 operates asynchronously from all other DSPAB clocks. In master mode, FSCLKN1 is derived from DSPAB's internal clock generator. The active edge of FSCLKN1 can be programmed by the DSP. BIDIRECTIONAL - Default: INPUT FLRCLKN1 -- PCM Audio Input Sample Rate Clock
89
Digital-audio frame clock input. FLRCLKN1 typically is run at the sampling frequency. FLRCLKN1 operates asynchronously from all other DSPAB clocks. The polarity of FLRCLKN1 for a particular subframe can be programmed by the DSP. BIDIRECTIONAL - Default: INPUT FSDATAN1 -- PCM Audio Data Input One Digital-audio data input that can accept from one compressed line or 2 channels of PCM data. FSDATAN1 can be sampled with either edge of FSCLKN1, depending on how FSCLKN1 has been configured. INPUT CMPCLK, FSCLKN2 -- PCM Audio Input Bit Clock Digital-audio bit clock input. FSCLKN2 operates asynchronously from all other DSPAB clocks. The active edge of FSCLKN2 can be programmed by the DSP. BIDIRECTIONAL - Default: INPUT CMPDAT, FSDATAN2 -- PCM Audio Data Input Number Two Digital-audio data input that can accept either one compressed line or 2 channels of PCM data. FSDATAN2 can be sampled with either edge of FSCLKN2, depending on how FSCLKN2 has been configured. BIDIRECTIONAL - Default: INPUT FDBCK -- Reserved This pin is reserved and should be pulled up with an external 3.3k resistor. INPUT FDBDA -- Reserved This pin is reserved and should be pulled up with an external 3.3k resistor. BIDIRECTIONAL - Default: INPUT PLLVDD -- PLL Supply Voltage 2.5 V PLL supply. PLLVSS -- PLL Ground Voltage PLL ground. RESET -- Master Reset Input Asynchronous active-low master reset input. Reset should be low at power-up to initialize the DSP and to guarantee that the device is not active during initial power-on stabilization periods. At the rising edge of reset the host interface mode of DSPAB is selected contingent on the state of the FHS0, FHS1, and FHS2 pins. At the rising edge of reset the host interface mode of DSPC is selected contingent on the state of the UHSO, UHS1, and UHS2 pins. If reset is low all bidirectional pins are high-Z inputs. INPUT TEST -- Reserved
90
This should be tied low for normal operation. INPUT MCLK -- Audio Master Clock Bidirectional master audio clock. As an output, MCLK provides a low jitter oversampling clock. MCLK supports all standard oversampling frequencies. BIDIRECTIONAL - Default: INPUT SCLK0 -- Audio Output Bit Clock Bidirectional digital-audio output bit clock for AUDATA0, AUDATA1, AUDATA2, and AUDATA3. As an output, SCLK0 can provide 32 Fs, 64 Fs, 128 Fs, 256 Fs, or 512 Fs frequencies and is synchronous to MCLK. As an input, SCLK0 is independent of MCLK. BIDIRECTIONAL - Default: INPUT SCLK1 -- Audio Output Bit Clock Bidirectional digital-audio output bit clock for AUDATA4, AUDATA5, AUDATA6, and AUDATA7. As an output, SCLK1 can provide 32 Fs, 64 Fs, 128 Fs, 256 Fs, or 512 Fs frequencies and is synchronous to MCLK. As an input, SCLK1 is independent of MCLK. BIDIRECTIONAL - Default: INPUT LRCLK0 -- Audio Output Sample Rate Clock Bidirectional digital-audio output frame clock for AUDATA0, AUDATA1, AUDATA2, and AUDATA3. As an output, LRCLK0 can provide all standard output sample rates up to 192 kHz and is synchronous to MCLK. As an input, LRCLK0 is independent of MCLK. BIDIRECTIONAL - Default: INPUT LRCLK1 -- Audio Output Sample Rate Clock Bidirectional digital-audio output frame clock for AUDATA4, AUDATA5, AUDATA6, and AUDATA7. As an output, LRCLK1 can provide all standard output sample rates up to 192 kHz and is synchronous to MCLK. As an input, LRCLK1 is independent of MCLK. BIDIRECTIONAL - Default: INPUT AUDATA0 -- Digital Audio Output 0 PCM digital-audio data output. OUTPUT AUDATA1 -- Digital Audio Output 1 PCM digital-audio data output. OUTPUT AUDATA2 -- Digital Audio Output 2 PCM digital-audio data output. OUTPUT AUDATA3, XMT958A -- Digital Audio Output 3, S/PDIF Transmitter
91
CMOS level output that outputs a biphase-mark encoded (S/PDIF) IEC60958 signal or digital audio data which is capable of carrying two channels of PCM digital audio. OUTPUT AUDATA4, GPIO28 -- Digital Audio Output 4, General Purpose I/O PCM digital-audio data output. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: OUTPUT AUDATA5, GPIO29 -- Digital Audio Output 5, General Purpose I/O PCM digital-audio data output. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: OUTPUT AUDATA6, GPIO30 -- Digital Audio Output 6, General Purpose I/O PCM digital-audio data output. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: OUTPUT AUDATA7, XMT958B, GPIO31 -- Digital Audio Output 7, S/PDIF Transmitter, General Purpose I/O CMOS level output that contains a biphase-mark encoded (S/PDIF) IEC60958 signal or digital audio data which is capable of carrying two channels of PCM digital audio. This pin can also act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: OUTPUT DBCK -- Debug Clock Must be tied high to 3.3k ohm resistor. INPUT DBDA -- Debug Data Must be tied high to 3.3k ohm resistor. BIDIRECTIONAL - Default: INPUT SLCKN, GPIO22 -- PCM Audio Input Bit Clock, General Purpose I/O Digital-audio bit clock that is an input. SCLKN operates asynchronously from all other DSPAB clocks. The active edge of SCLKN can be programmed by the DSP. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT LRCLKN, GPIO23 -- PCM Audio Input Sample Rate Clock, General Purpose I/O Digital-audio frame clock input. LRCLKN operates asynchronously from all other DSPAB clocks. The polarity of LRCLKN for a particular subframe can be programmed by the DSP. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT SDATAN0, GPIO24 -- PCM Audio Input Data, General Purpose I/O Digital-audio PCM data input. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT SDATAN1, GPIO25 -- PCM Audio Input Data, General Purpose I/O
92
Digital-audio PCM data input. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT SDATAN2, GPIO26 -- PCM Audio Input Data, General Purpose I/O Digital-audio PCM data input. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT SDATAN3, GPIO27 -- PCM Audio Input Data, General Purpose I/O Digital-audio PCM data input. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT SCS -- Host Serial SPI Chip Select SPI mode active-low chip-select input signal. INPUT SCCLK -- Serial Control Port Clock This pin serves as the serial SPI clock input. INPUT SCDIN -- SPI Serial Control Data Input In SPI mode this pin serves as the data input pin. INPUT SCDOUT, SCDIO -- Serial Control Port Data Input and Output In SPI mode this pin serves as the data output pin. BIDIRECTIONAL - Default: OUTPUT in SPI mode INTREQ -- Control Port Interrupt Request Open-drain interrupt-request output. This pin is driven low to indicate that DSPC has outgoing control data and should be serviced by the host. OPEN DRAIN I/O - Requires 3.3K Ohm Pull-Up
93
HDATA7, GPIO7 -- DSPC Bidirectional Data Bus, General Purpose I/O HDATA6, GPIO6 HDATA5, GPIO5 HDATA4, GPIO4 HDATA3, GPIO3 HDATA2, GPIO2 HDATA1, GPIO1 HDATA0, GPIO0 In parallel host mode, these pins provide a bidirectional data bus. These pins can also act as general purpose input or output pins that can be individually configured and controlled by DSPC. These pins have an internal pull-up. BIDIRECTIONAL - Default: INPUT A0, GPIO13 -- Host Parallel Address Bit 0, General Purpose I/O In parallel host mode, this pin serves as the LS Bit of a two bit address input used to select one of four parallel registers. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT A1, GPIO12 -- Host Address Bit 1, General Purpose I/O In parallel host mode, this pin serves as the MS Bit of a two bit address input used to select one of four parallel registers. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT RD, R/W, GPIO11 -- Host Parallel Output Enable, Host Parallel R/W, General Purpose I/O In Intel parallel host mode, this pin serves as the active-low data bus enable input. In Motorola parallel host mode, this pin serves as the read-high/write-low control input signal. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. This pin has an internal pull-up. BIDIRECTIONAL - Default: INPUT WR, DS, GPIO10 -- Host Write Strobe, Host Data Strobe, General Purpose I/O In Intel parallel host mode, this pin serves as the active-low data bus enable input. In Motorola parallel host mode, this pin serves as the read-high/write-low control input signal. In serial host mode, this pin can serve as a general purpose input or output bit. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. This pin has an internal pull-up. BIDIRECTIONAL - Default: INPUT CS, GPIO9 -- Host Parallel Chip Select, General Purpose I/O In parallel host mode, this pin serves as the active-low chip-select input signal. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. This pin has an internal pull-up. BIDIRECTIONAL - Default: INPUT
94
HINBSY, GPIO8 -- Input Host Message Status, General Purpose I/O This pin indicates that serial or parallel communication data written to the DSP has not been read yet. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. This pin has an internal pull-up. BIDIRECTIONAL Default: OUTPUT SD_DATA15, EXTA18 -- SDRAM Data Bus, SRAM External Address Bus SD_DATA14, EXTA17 SD_DATA13, EXTA16 SD_DATA12, EXTA15 SD_DATA11, EXTA14 SD_DATA10, EXTA13 SD_DATA9, EXTA12 SD_DATA8, EXTA11 SDRAM data bus 15:8. SRAM external address bus 18:11. OUTPUT SD_DATA7, EXTD7 -- SDRAM Data Bus, SRAM External Data Bus SD_DATA6, EXTD6 SD_DATA5, EXTD5 SD_DATA4, EXTD4 SD_DATA3, EXTD3 SD_DATA2, EXTD2 SD_DATA1, EXTD1 SD_DATA0, EXTD0 SDRAM data bus 7:0. SRAM external data bus 7:0. BIDIRECTIONAL - Default: INPUT SD_ADDR10, EXTA10 -- SDRAM Address Bus, SRAM External Address Bus SD_ADDR9, EXTA9 SD_ADDR8, EXTA8 SD_ADDR7, EXTA7 SD_ADDR6, EXTA6 SD_ADDR5, EXTA5 SD_ADDR4, EXTA4 SD_ADDR3, EXTA3 SD_ADDR2, EXTA2 SD_ADDR1, EXTA1 SD_ADDR0, EXTA0 SDRAM address bus 10:0. SRAM external address bus 10:0. OUTPUT
95
SD_CLK_OUT -- SDRAM Clock Output SDRAM clock output. OUTPUT SD_CLK_IN -- SDRAM Re-timing Clock Input SDRAM re-timing clock input. INPUT SD_CLK_EN -- SDRAM Clock Enable SDRAM clock enable. OUTPUT SD_BA, EXTA19 -- SDRAM Bank Address Select, SRAM External Address Bus SDRAM bank address select. SRAM external address bus 19. OUTPUT SD_CS -- SDRAM Chip Select SDRAM chip select. OUTPUT SD_RAS -- SDRAM Row Address Strobe SDRAM row address strobe. OUTPUT SD_CAS -- SDRAM Column Address Strobe SDRAM column address strobe. OUTPUT SD_WE -- SDRAM Write Enable SDRAM write enable. OUTPUT SD_DQM1 -- SDRAM Data Mask 1 SDRAM data mask 1. OUTPUT SD_DQM0 -- SDRAM Data Mask 2 SDRAM data mask 0. OUTPUT NV_CS, GPIO14 -- SRAM Chip Select, General Purpose I/O SRAM/Flash chip select. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: OUTPUT NV_OE, GPIO15 -- SRAM Output Enable, General Purpose I/O SRAM/Flash output enable. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: OUTPUT
96
NV_WE, GPIO16 -- SRAM Write Enable, General Purpose I/O SRAM/Flash write enable. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: OUTPUT UHS2, CS_OUT, GPIO17 -- Mode Select Bit 2, External Serial Memory Chip Select, General Purpose I/O DSPC control port mode select bit 2. This pin is sampled at the rising edge of RESET and is one of three pins used to select the control port mode. In serial control port mode, this pin can serve as an output to provide the chip-select for a serial EEPROM. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT UHS0, GPIO18 -- Mode Select Bit 0, General Purpose I/O DSPC control port mode select bit 0. This pin is sampled at the rising edge of RESET and is one of three pins used to select the control port mode. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT UHS1, GPIO19 -- Mode Select Bit 1, General Purpose I/O DSPC control port mode select bit 1. This pin is sampled at the rising edge of RESET and is one of three pins used to select the control port mode. This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. BIDIRECTIONAL - Default: INPUT GPIO20 -- General Purpose I/O This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC. This pin has an internal pull-up. BIDIRECTIONAL - Default: INPUT GPIO21 -- General Purpose I/O This pin can act as a general-purpose input or output that can be individually configured and controlled by DSPC.This pin has an internal pull-up. BIDIRECTIONAL - Default: INPUT VDD[7:1] -- 2.5V Supply Voltage 2.5V supply voltage. VSS -- 2.5V Ground 2.5V ground.
97
NC[5:1] -- No Connect Recommended tie to ground. VDDSD[4:1] -- 3.3V SDRAM/SRAM/EPROM Interface Supply 3.3V SDRAM/SRAM/EPROM supply. VSSSD -- 3.3V SDRAM/SRAM/EPROM Interface Ground 3.3V ground.
13. ORDERING INFORMATION
CS494002-CQ 144-pin, accommodates SRAM/SDRAM CS494502-CQ 100-pin, external SRAM memory interface only (no SDRAM), no parallel-control ports, no FLASH programming. (Contact the factory for the 100-pin package pin-out and dimension drawing) Temp Range 0-70 C for both parts
98
14. PACKAGE DIMENSIONS 14.1 144-Pin LQFP Package
E E1
D D1
1
Note: See Legend Below
L
e
B A A1
Figure 59. 144-Pin LQFP Package Drawing
DIM A A1 B D D1 E E1 e L
MIN --0.002 0.007 0.854 0.783 0.854 0.783 0.016 0.000 0.018
INCHES NOM 0.55 0.004 0.008 0.866 BSC 0.787 BSC 0.866 BSC 0.787 BSC 0.020 4 0.024
MAX 0.063 0.006 0.011 0.878 0.791 0.878 0.791 0.024 7.000 0.030
MILLIMETERS MIN --0.05 0.17 21.70 19.90 21.70 19.90 0.40 0.00 0.45
99

▲Up To Search▲

Price & Availability of CS49400

	To Download CS49400 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .